Advertisement
Quick Links
F
T
I R S T
H I N G S
In this preface, see how
To make sure you have everything
To operate with safety
To get to know your Waverunner scope
To install and power up
To initialize
To check the system status
To install new software and firmware
To activate the screen saver
To use menus, menu buttons and knobs
To choose button and knob preferences
2
First
. . .
ISSUED: January 2002
LTXXX-OM-E Rev B
Advertisement
Related Manuals for Teledyne LeCroy Waverunner LT Series
Summary of Contents for Teledyne LeCroy Waverunner LT Series
- Page 1 First . . . I R S T H I N G S In this preface, see how To make sure you have everything To operate with safety To get to know your Waverunner scope To install and power up To initialize To check the system status To install new software and firmware...
-
Page 2: Che Ck That You Have E Ve Rythin G
WhenYourWaverunneris Delivered CHE CK THAT YOU HAVE E VE RYTHIN G First, verify that all items on the packing list or invoice copy have been shipped to you. (The items are also listed below .) Second, check the SYSTEM STATUS display once your Waverunner oscilloscope is installed (see page 12). -
Page 3: Stay Up-To-Date
I R S T H I N G S TAKE ADVAN TAGE OF MAIN TE N AN CE AGRE E ME N TS We offer a variety of services under the heading of Maintenance Agreements. These give extended warranty and allow you to budget maintenance costs after the initial three-year warranty has expired. Installation, training, enhancements, and on-site repairs —... - Page 4 First ScopeE xplorer is a highly practical PC-based connectivity tool that interfaces Waverunner to a PC that is running Microsoft Windows, via the rear panel GPIB (IE EE 488) or RS-232 port. Specially designed by LeCroy for its oscilloscopes, ScopeExplorer allows you to perform data and image transfers and other remote operations from scope to PC with just a few keyboard strokes or mouse clicks.
- Page 5 I R S T H I N G S Safety First OPE RATE IN A SAFE E N VIRON ME N T : Waverunner has been qualified Before installing your Waverunner, ensure that its operating to the following E N 61010-1category: environment will be maintained within these parameters: Protection Class Temperature: 5 to 40 °C (41 to 104 °F)
- Page 6 First : Waverunner automatically Protective Conductor Terminal adapts to the line voltage present: Chassis Terminal 115V 45–66 Hz (90–132V) Alternating Current Only 220V 45–66 Hz (180–250 V) Denotes a hazard. If a WARNING is indicated on the instrument, do not proceed until its WARNING conditions are understood and met (see also CAUTION).
- Page 7 I R S T H I N G S RE PLACE WITH THE CORRE CT FUSE S For continued fire protection at all line voltages, replace fuses only with those of the specified type and rating. Disconnect the power cord before inspecting or replacing a fuse. Open the fuse holder (located directly to the left of the mains power plug) using a small, flat-bladed screwdriver.
- Page 8 First Up and Running GE T TO KN OW YOUR WAVE RUN N E R – FRON T PAN E L Display Menu Controls AUTO SE T UP Floppy Disk Drive Timebase Controls AUTO SETUP TRIGGER ZERO DELAY SETUP STOP AUTO NORMAL SINGLE DELAY...
- Page 9 I R S T H I N G S Before a display appears, the instrument will automatically perform hardware and software self-tests, followed by a full system calibration. The front panel STANDBY L ED will be lit during this sequence. The full testing procedure will take about 10 seconds, after which a display appears.
- Page 10 First AV I G A T E H R O U G H E N U S Menus such as enable you to perform actions or adjust settings. The menu button beside each displayed menu controls that menu. L onger menus that span the breadth of two buttons are controlled by both buttons.
- Page 11 I R S T H I N G S IN ITIALIZE Initialize your Waverunner scope to its basic default waveform display settings: PANELS Press to display the PANEL SETUPS menu group. If Recall is not selected, press the button once to select it: Then press the button beside Initialize to Waverunner default settings whenever you wish to clear your settings and make a fresh start on a new measurement.
- Page 12 First ADD AN OPTION This menu will also be displayed when you select System: Use it to install new options — without the need to return your Waverunner for a refit. Press that menu’s button to display Then press that menu’s button to display the ADD OPTION menus. Use them whenever you wish to add a Waverunner option by means of a special code.
- Page 13 I R S T H I N G S Press its button, then select Yes or N o from When enabled, the built-in screen saver is activated 10 minutes after the last use of a front panel control. This is a complete display shutdown of the internal screen — an “Energy-Saver.” The front panel LED light will indicate when the scope is in the screen-saving STANDBY state.