Nordson Encore HD Operator Card
Manual powder spray system with prodigy pump cabinet
Hide thumbs
Also See for Encore HD:
- Customer product manual (273 pages) ,
- Product manual (68 pages) ,
- Customer product manual (61 pages)
Advertisement
Quick Links
Nordson Corporation
OPERATOR'S CARD
P/N 1604871-01
Encorer HD Manual Powder Spray System with
Prodigyr Pump Cabinet
WARNING: Allow only qualified personnel to
perform the following tasks. Follow the
safety instructions in this document and all
other related documentation.
System Diagram
Gun 2
Fluidizing Air
Figure 1 System Diagram (Two-Gun System Shown)
Gun 2
Controller
Pump 2
Pump Control
System Air
Fluidizing Air
Regulator
Refer to component operator manuals for more
information on safety, setup, operation,
troubleshooting, repair and parts.
Gun 1
Controller
Pump 1
Panel
Power
Switch
Pump
Adapters
Powder
Hopper
1
Gun 1
System
Power
Advertisement
Related Manuals for Nordson Encore HD
Summary of Contents for Nordson Encore HD
- Page 1 Nordson Corporation OPERATOR’S CARD P/N 1604871-01 Encorer HD Manual Powder Spray System with Prodigyr Pump Cabinet WARNING: Allow only qualified personnel to Refer to component operator manuals for more information on safety, setup, operation, perform the following tasks. Follow the troubleshooting, repair and parts.
-
Page 2: Controller Interface
Setting A Setting Setting Icons Pattern Air Flow Setting Function/Help Display Help Button Rotary Knob Nordson Button (Configuration) Standby Button View Button Enter Button Color Change Button Figure 2 Controller Interface The Setpoint icons light to indicate the configured or Help Codes selected setpoints. - Page 3 Assist Air Setting, Fast Flow Setting, and Software Versions The View button allows the user access to Figure 4 Assist Air Settings>>> 1 <<< adjust Assist Air and Fast Flow preset values, and to view software versions. Fast Flow Setting Press the View button consecutively to display, in order, the following functions: Assist Air Setting (AA), The Fast Flow setting allows you to specify Fast Flow...
- Page 4 2. Turn the rotary knob to increase or decrease the 5. The preset number will begin blinking, indicating a kV setpoint. The setpoint is automatically saved if change has been made. To save the new it does not change for 3 seconds, or when any settings, press the Enter button.
- Page 5 1. To set or change kV, press the kV button. The button LED lights to show that kV is selected. 2. Turn the rotary knob to increase or decrease the kV setpoint. The setpoint is automatically saved if it does not change for 3 seconds, or when any button is pressed.
- Page 6 2. Turn the knob to increase or decrease the setpoints. The setpoint is automatically saved if it does not change for 3 seconds or when any button is pressed. Percent Flow Icon Flow Button Pattern Button Pattern Icon Figure 13 Flow Rate and Pattern Setpoints...
-
Page 7: Purge Operation
Purge Operation HDLV System Purge 2. Soft Purge − Assist air is directed through the pump and siphon tubing back to the powder Press the Color Change button on the controller and supply (Soft Siphon), then through the pump and then press Enter o. - Page 8 Press the Enter button to save the change and exit the value, so that rotating the knob now scrolls through the function numbers again. Press and hold the Nordson button for 5 seconds. The Function/Help display lights to show the function numbers and values. Use the functions to configure the controller for your application.>>>...
- Page 9 Table 1 Function Settings Function Number Function Name Gun Type Fluidizing Display Units Electrostatic Control Powder Flow Control Keypad Lockout Vibratory Box Delay Off Maintenance Timer, Gun Setting Trigger Function Help Codes Zero Reset (Flow) Gun Display Errors A Lower Limit A Upper Limit Total Hours Save/Restore/Reset...
-
Page 10: Spray Gun Operation
Spray Gun Operation The spray gun interface and settings trigger allow you to change the preset or the powder flow settings, or purge the gun, without using the controller interface. Preset Mode Icon Flow Mode Icon Settings Trigger Increase/On Display Purge Button Mode Button Decrease/Off... - Page 11 Periodically check all system ground connections. Issued 1/14 Original copyright date 2014. Prodigy, Encore, HDLV, Nordson, and the Nordson logo are registered trademarks of Nordson Corporation.