Startec-1200 Contents Introduction ......................5 1.1 Safety Rules .....................6 Installation .......................6 2.1 Mounting ......................6 2.1.1 Clamps (Hooks) ..................6 2.2 Secure the 0 ..................7 2.3 Connectors .......................7 2.3.1 AC Connectors..................7 2.3.2 DMX .......................7 2.4 Fuse........................7 The Menu Field ......................8 3.1 Adjust the DMX- Address..................8 3.2 Read out the Running Time of Lamp and Unit..........9...
Page 4
Startec-1200 Change the Gobos ....................14 6.1 Safety Rules ....................14 6.2 How to change the Gobos ................14 Maintenance the 0 ................15 7.1 Mirror and Optical System ................15 Technical Data /Overview ..................16 German Light Production (V2.1)
Startec-1200 Introduction Mirror Handles Menu-Panel D M X A dress H ours M ode Service M enu C ursor D ata- D ata+ gobowheel Color-Wheel Asphere Lamp (fillerneck up) Concave mirror Snaps Fuse lamp Fuse electronic 10 AT 4 AT...
Startec-1200 1.1 Safety Rules 0 is a High-Tech Product. To guarantee a smooth operation, it is necessary to keep following rules. 1. Make sure that the Mirror of the 0 , can move without any mechanical problems and that all fan openings are clean and not blocked by anything.
Startec-1200 0 is fully operational whether it stands or hangs. Using the 0 standing on the ground requires a rough but even surface. Make sure that the fan openings are not blocked by any circumstances and that the system is secured against tip over.
Startec-1200 The Menu Field 3.1 Adjust the DMX- Address Right after turning on the 0 you can see the current DMX- Address. Choose this as follows. Select the DMX- Level by pressing the menu key once. Count up or down the DMX- Address with the Data + or Data – buttons. After pushing the Cursor button the upcounting speed increases to a multiple.
Startec-1200 3.2 Read out the Running Time of Lamp and Unit Select the time level by pressing the Menu key twice. Select the requested time by pressing the Cursor key, 3.2.1 Lamp Time 1 The current lamp time is shown alternating with LA 1.
Startec-1200 3.4 The Test Level The Test Level makes a function test or a selftest procedure possible. 3.4.1 Selftest Procedure Select the requested test level by pressing the Cursor key. Start the Selftest program by pressing the Data+ key. The lamp can be started by pressing the Data+ and Data- keys for 5 seconds at the same time.
Startec-1200 Change the Lamp For a hassle free change of the Light bulb, it is absolutely necessary to follow all descriptions in this chapter step by step. 5.1 Safety Rules • Unplug AC power connection • Allow to cool (min. 30 minutes) •...
Startec-1200 Change the Gobos 0 is fitted with standard Gobos (∅ 37,5 mm, picturesize 27 mm). 6.1 Safety Rules • Unplug AC power connection • Allow to cool (over 30 minutes) • Don’t touch lamp with bare fingers. • Close the 0 before you connect the AC power! 6.2 How to change the Gobos...
Maintenance the The cleaning of the inner optical System, color filters, color correction filter and lenses should be done by qualified person only! Contact your local GLP Dealer for details. Use no strong detergents, acid etc. for cleaning the case.
Startec-1200 Technical Data /Overview • Supply Data 230V/10AT • 1200 HMI Lamp, bilateral based, with 750h Lamp Life • Capacitor compensation • Angle of spread 16° • DMX 512 Standard • weight 35 kg • Dimensions: 880 x 220 x 360 mm •...
Page 17
Startec-1200 German Light Production (V2.1)