Tektronix 7B92 Instruction Manual page 23

Dual time base
Hide thumbs Also See for 7B92:
Table of Contents

Advertisement

Calibration-7B92 Service
TEST EaU IPMENT
Examples of Applicable
Description
Minimum Specifications
Usage
Test Equipment
1. Calibration
Tektronix
7000-Series.
500
Used throughout procedure
a. Tektronix 7904 Oscillo-
Oscilloscope
megahertz bandwidth.
to provide a display.
scope.
2. Amplifier Plug-in
Tektronix 7A-Series. 50 milli-
External trigger level range
a. 7A15A,
7A16,
7A18
Unit
volts to five volts/div deflection
checks. Delayed sweep base-
Amplifier Units.
factor.
line adjustment.
b. Other
7A-Series
plug-in
units may be used.
3. Wide-Band Amplifier
Tektronix 7 A-Series. 500 mega-
Used throughout procedure
a. Tektronix
7A19 Ampli-
Plug-in Unit
hertz bandwidth.
to provide vertical input to
fier.
oscilloscope system.
4. 10X Passive Probe
Compatible
with
7A-Series
Line
triggering
check.
a. Tektronix P6053 Probe.
Amplifiers.
Delayed
sweep
baseline
adjustment.
5. Differential Sampling
System risetime at least 350
Delay Pickoff TD bias adjust-
a. Tektronix
7S12
TOR/
- j
System
picoseconds; pulse amplitude,
ment.
High-frequency
lin-
Sampler plug-in Unit with S-1
200 millivolts input; differential
earity
checks
and
adjust-
Sampling
Head
and
S·52
sensitivity, 100 millivolts.
ments.
Pulse Generator Head, and a
7S11 vertical sampling plug-in
unit with a S-1 Sampling
Head.
6. Fast-Rise Pulse
Pulse
output;
positive-going
Oelay pickoff TO bias adjust-
a. Tektronix S-52 Pulse Gen-
j
Generator
pulse with 200 millivolts ampli-
ment.
erator Head used with 7S12
tude. Risetime equal to or less
TOR/Sampler or Type 285
than 70 picoseconds.
Power Supply.
l
_.J
b. Tektronix Type 284 Pulse
Generator.
7. Time-Mark Generator
Marker
outputs,
two
nano-
Sweep timing checks and ad-
a. Tektronix
2901
Time·
J
seconds to 0.5 second; marker
justments.
Sweep
delay
Mark Generator.
accuracy, within 0.1 %.
checks and adjustments.
b. Tektronix Type 184 Time-
Mark Generator.
8. Low· Frequency
Frequency, 30 hertz to 50 kilo-
Low-frequency
triggering
a. General
Radio
1310-B
Sine-wave Generator
hertz; output amplitude, variable
checks.
Oscillator.
from 50 millivolts to 10 volts.
J
9. Medium-Frequency
Frequency, 20 megahertz to 100
20
megahertz
triggering
a. Tektronix Type 191 Con-
Constant-Ampl itude
megahertz;
output
amplitude
checks.
stant Amplitude Signal Gen-
Signal Generator
variable from 100 millivolts to
erator.
J
500 millivolts.
10. High-Frequency
Frequency, 100 megahertz to
T rigger TO bias and runs after
a. Tektronix
067-0532-01
Constant-Amplitude
500 megahertz; reference fre-
sensitivity adjustments. HF
Calibration Fixture.
Signal Generator
quency, 10 megahertz or lower;
SYNC
operation
checks.
b. Te ktronix
067-0650-00
output amplitude, variable from
Trigger jitter checks.
Calibration Fixture.
0.5 to four volts; amplitude
accuracy, constant within 1% of
c. General Radio 1362 UH F
J
reference as output frequency
Oscillator
with
1263-C
changes.
Ampl itude-Regulation Power
Supply.
l
J
d. Wiltron
Model
610B
Swept Frequency Generator
with Model 6108B, 10 to
1220 megahertz plug-in.
]
4-2
®
]
SctlllS
by Outsource-Qptions
=>

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 7B92 and is the answer not in the manual?

Subscribe to Our Youtube Channel

Table of Contents