YASKAWA GA800 Series Technical Reference page 1013

Overload ............................................................. 943
PF ..................................................................... 941
rr ...................................................................... 947
Software Current Limit Selection ................................ 943
Pulse Train Input
Terminal RP Function Selection.................................. 892
Pulse Train Input/Output
Parameter ............................................................ 891
Pulse train output
Terminal MP function selection .................................. 894
Wiring specifications............................................... 102
PWEr...................................................................... 358
R
Rating (200 V)
Drive ................................................................. 434
Rating (400 V)
Drive ................................................................. 436
rdEr........................................................................ 359
Ready
LED status........................................................... 141
Remove
Front cover ........................................................... 46
Keypad ................................................................ 39
Terminal cover ....................................................... 46
RESET key............................................................... 135
Restore
Parameters (Auto Backup) ........................................ 187
Parameters (keypad to drive) ..................................... 167
Reverse Operation Selection........................................... 664
rF .......................................................................... 334
rH.......................................................................... 334
RJ-45 connector ......................................................... 135
Rotational Auto-Tuning
Induction Motor .................................................... 191
PM Motors .......................................................... 192
Precautions .......................................................... 198
rr ........................................................................... 334
Protective function ................................................. 947
rUn ........................................................................ 345
RUN
LED status........................................................... 141
Run command
LOCAL/REMOTE Run selection ................................ 660
Switching between LOCAL/REMOTE ......................... 660
Run Command at Power Up ........................................... 670
Run Command Selection 2
Switching between LOCAL/REMOTE ......................... 669
RUN indicator ..................................................... 135, 138
RUN key ................................................................. 135
S
S-curve characteristics
Parameter ............................................................ 716
Sampling time setting
Data log .............................................................. 184
SC ......................................................................... 334
SCF........................................................................ 335
SE ......................................................................... 345
SEr ........................................................................ 335
Serial communication terminals
MEMOBUS/Modbus Communications .......................... 96
Set date and time
Operation ............................................................ 177
YASKAWA SIEPC71061737B GA800 Drive Technical Reference
Set time
Operation ............................................................ 177
Setup Wizard
Operation ............................................................ 179
Short Circuit Braking
Parameter ............................................................ 671
Side-by-side
Derating.............................................................. 945
Simple Positioning Stop................................................ 751
Slip compensation
Parameter ............................................................ 717
Softcharge Relay Maintenance Set ................................... 989
Software Current Limit Selection
Protective function ................................................. 943
Software version
Display procedure .................................................. 186
Speed Agreement
Parameter ............................................................ 927
Speed Detection
Parameter ............................................................ 927
Speed Estimation Speed Search ....................................... 676
Speed limit
Parameter ............................................................ 752
Speed Search function
Operation during momentary power loss........................ 912
Parameter ............................................................ 674
Stall Prevention function
Parameter ............................................................ 917
Stationary Auto-Tuning
Induction Motor .................................................... 191
PM Motors .......................................................... 192
Precautions .......................................................... 198
Stationary Auto-Tuning for Line-to-Line Resistance .............. 191
Precautions .......................................................... 199
Stator resistance Auto-Tuning ......................................... 192
Precautions .......................................................... 199
STo ........................................................................ 345
SToF ...................................................................... 345
Stop command
LOCAL/REMOTE Run selection ................................ 660
STOP key................................................................. 135
STOP Key Function Selection......................................... 983
Stopping Method Selection ............................................ 661
STPo ...................................................................... 335
Surge protective device
Connection .......................................................... 121
SvE ........................................................................ 335
T
Temperature
Environment.......................................................... 34
Terminal block............................................................ 96
Configuration of main circuit terminal block.................... 65
Control circuit terminal block functions.......................... 93
I/O terminals function selection switches ....................... 101
Terminal function selection ............................................ 103
Terminal A1 ................................................... 101, 103
Terminal A2 ................................................... 101, 103
Terminal A3 ................................................... 101, 104
Terminal AM.................................................. 101, 104
Terminal FM .................................................. 101, 104
Termination resistor
Setting switch ....................................................... 105
1013