Advertisement
Quick Links
Advertisement
Related Manuals for GMC Magne Charge WM7200
Summary of Contents for GMC Magne Charge WM7200
- Page 1 WM7200 Inductive Charger Installation Manual...
- Page 2 Before beginning the installation process, please read this installation manual completely, including the important safety instructions. ,PSRUWDQW6DIHW\,QVWUXFWLRQV SAVE THESE INSTRUCTIONS - This installation manual contains important instructions that should be followed during the installation of Magne Charge™ Inductive Charger Model WM7200. Carefully read these instructions before installing this charger.
- Page 3 GROUNDING INSTRUCTIONS - This charger must be connected to a permanently grounded wiring system. An equipment-grounding conductor should be run with circuit conductors and connected to the equipment-grounding lead on the battery charger. Connections to the battery anger charger should comply with all local codes and ordinances. NOTICE: Do not install the charger in a location that exposes it to extreme heat.
- Page 4 6LWH3UHSDUDWLRQ The following guidelines are presented for site preparation: Input Power Specifications Voltage 208 - 240 Vac, 60 Hz Service Requirement 40 Amp Service Dimensions Height 655 mm (26 in) Width 403 mm (16 in) Depth 311 mm (12 in) Cable Length 2.9 m (9 ft 7 in) Weight...
- Page 5 ,QVWDOODWLRQ5HTXLUHPHQWV Be certain you read all installation requirements and instructions before performing this installation. 1. This charger requires a dedicated branch circuit rated at 208 - 240 Vac (single phase) with a minimum circuit capacity of 40 Amps and over-current protection of 40 Amps. NOTICE: Do not install a Ground Fault Circuit Interrupter (GFCI) in the branch circuit.
- Page 6 :DOO0RXQW,QVWDOODWLRQ Inspection (Refer to figures 1 & 2) 1. Remove the charger from its shipping container. Note that the shipping container and packaging material are re-useable. Do not destroy. Save these items, or return them to your distributor. 2. Make certain the coupler paddle is in its holster. 3.
-
Page 7: Site Clean Up
15. Connect the flexible non-metallic conduit to the charger power source (e.g. junction box). Do not cut conduit or input wiring. 16. Connect the wires using UL listed waterproof wire nuts in the following manner (Note that the supply-side wire may be a different gauge wire): Input power 208 - 240 Vac, Single phase Line 1 (HOT) - Page 8 :DOO0RXQW)LJXUHV Top Mounting Holster Bracket Holes Cable Coupler Hook Paddle Display Input Wiring Output Cable FRONT BACK FIGURE 1 - FRONT & BACK VIEWS Delay Button Bottom Mounting Bracket Holes CCID Test (One on each corner) Button CCID Reset Button FIGURE 2 - BOTTOM OF CHARGER...
- Page 9 Top Mounting Bracket 78.6 cm (31 in) Bottom Mounting Bracket FIGURE 3 - BRACKET INSTALLATION FIGURE 4 - MOUNTING HEIGHT...
- Page 10 )ORRU0RXQW,QVWDOODWLRQ Inspection (Refer to figures 5 & 6) 1. Remove the charger from its shipping container. Note that the shipping container and packaging material are re-useable. Do not destroy. Save these items, or return them to your distributor. 2. Make certain the coupler paddle is in its holster. 3.
- Page 11 15. Connect the wires using UL listed waterproof wire nuts in the following manner (Note that the supply-side wire may be a different gauge wire): Input power 208 - 240 Vac, Single phase Line 1 (HOT) Black Wire Line 2 (HOT) Black Wire Ground Green Wire...
- Page 12 )ORRU0RXQW)LJXUHV Holster Cable Coupler Hook Paddle Display Output Input Cable Wiring FIGURE 5 - FRONT VIEW Delay Button Bottom Mounting Bracket Holes CCID Test (One on each corner) Button CCID Reset Button FIGURE 6 - BOTTOM OF CHARGER...
- Page 13 Side Opening (Cover plate is installed from outside of pedestal) Pedestal Hole for Conduit Fitting Access Panel Pedestal Mounting Holes (Two on each side) FIGURE 7 - PEDESTAL INSTALLATION...
- Page 14 78.6 cm (31 in) Curb or Mounting Base 15.2 cm (6 in) FIGURE 8 - MOUNTING HEIGHT...
- Page 15 281.94 mm Conduit Junction (11.10 in) Fitting Nut 4x ∅ 13.49 Charger Conduit 133.35 mm 133.35 mm (5.25 in) (5.25 in) Conduit Fitting Utility ∅ 355.6 mm Conduit (14.00 in) FIGURE 9 - PEDESTAL HOLE LOCATIONS FIGURE 10 - J-BOX INSTALLATION 2 m 92 cm Charger (9 ft 7 in)
- Page 16 *HQHUDO,QIRUPDWLRQ NOTICE: Changes or modifications to this product by other than an authorized service facility could void the product warranty. 1. This installation manual includes the latest information available at the time of printing. General Motors Advanced Technology Vehicles (GM ATV) reserves the right to make changes to this product without further notice.
- Page 17 *0$'9$1&('7(&+12/2*<9(+,&/(6 Torrance, California 90509-2923 1-800-482-6644 Listed EV Battery Charger 7M60 P/N 27005583 Magne Charge™ is a trademark of GM ATV ©1998 GM ATV...