1. Manuals
  2. Brands
  3. AGI Manuals
  4. Farm Equipment
  5. Storm Professional 2017 Series
  6. Operator's manual

AGI Storm Professional 2017 Series Operator's Manual

Seed treater
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Professional Series – 2017
Seed Treater
Operator's Manual
Original Instructions
Read this manual before using product. Failure to
follow instructions and safety precautions can
result in serious injury, death, or property
damage. Keep manual for future reference.
Part Number: 4400–90001
Revised: March 2020

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Storm Professional 2017 Series and is the answer not in the manual?

Questions and answers

Related Manuals for AGI Storm Professional 2017 Series

Summary of Contents for AGI Storm Professional 2017 Series

  • Page 1 Professional Series – 2017 Seed Treater Operator’s Manual Original Instructions Read this manual before using product. Failure to Part Number: 4400–90001 follow instructions and safety precautions can Revised: March 2020 result in serious injury, death, or property damage. Keep manual for future reference.
  • Page 2 We strongly recommend that all personnel associated with this equipment be trained in the correct operational and safety procedures required for this product. This product has been designed and constructed according to general engineering standards, other local regulations may apply and must be followed by the operator. Use the sign-off sheet below to record initial and periodic reviews of this manual with all such personnel.

  • Page 3: Table Of Contents

    PROFESSIONAL SERIES – 2017 – SEED TREATER CONTENTS 1. Introduction ............................6 1.1 Serial Number Location......................6 1.2 Intended Use ..........................6 1.2.1 Misuse ........................7 2. Safety............................... 8 2.1 Safety Alert Symbol and Signal Words..................8 2.2 General Product Safety ......................8 2.3 Rotating Flighting Safety ......................
  • Page 4 PROFESSIONAL SERIES – 2017 – SEED TREATER 7.2 Pre-Season Tasks ........................35 7.3 Conveyor Break-In ........................35 7.4 Treating Seed........................... 36 7.4.1 Create a Job......................36 7.4.2 Calibrate the Pumps....................37 7.4.3 Operate the Treater & Treat Seed ................39 7.4.4 Update the Calibration.....................
  • Page 5 PROFESSIONAL SERIES – 2017 – SEED TREATER 10.2.4 Installing Software....................73 11. Specifications ............................74 12. STORM Warranty..........................75 4400–90001...

  • Page 6: Introduction

    1. INTRODUCTION PROFESSIONAL SERIES – 2017 – SEED TREATER 1. Introduction Thank you for purchasing a STORM Seed Treater. Follow the instructions in this manual for safe use of the seed treater. With proper care, yourseed treater will provide you with many years of trouble-free operation.

  • Page 7: Misuse

    PROFESSIONAL SERIES – 2017 – SEED TREATER 1. INTRODUCTION • capacity at 22.5-45 bu/min (1350-2700 lb/min). • a suitable hopper bin or truck hopper. Use in any other way is considered as contrary to the intended use and is not covered by the warranty. 1.2.1 Misuse Do not install/use the seed treater for/with: •...

  • Page 8: Safety

    2. SAFETY PROFESSIONAL SERIES – 2017 – SEED TREATER 2. Safety 2.1. Safety Alert Symbol and Signal Words This safety alert symbol indicates important safety messages in this manual. When you see this symbol, be alert to the possibility of injury or death, carefully read the message that follows, and inform others.

  • Page 9: Rotating Flighting Safety

    PROFESSIONAL SERIES – 2017 – SEED TREATER 2. SAFETY 2.3. Rotating Flighting Safety • KEEP AWAY from rotating flighting. • DO NOT remove or modify flighting guards, doors, or covers. Keep in good working order. Have replaced if damaged. • DO NOT operate the seed treater without all guards, doors, and covers in place.

  • Page 10: Seed Treatment Safety

    2. SAFETY PROFESSIONAL SERIES – 2017 – SEED TREATER 2.7. Seed Treatment Safety Hazards associated with handling, sorting, mixing and storage of treated seed and seed treatments can be minimized by following the safety precautions listed below. The below are guidelines only and vary based on the type of seed treatment being used.

  • Page 11: Guards Safety

    PROFESSIONAL SERIES – 2017 – SEED TREATER 2. SAFETY 2.10. Guards Safety • Keep guards in place. Do not operate with guard removed. • Do not walk on, step on, or damage guards. • Lock out power before removing a guard. •...

  • Page 12: Towing The Seed Treater

    2. SAFETY PROFESSIONAL SERIES – 2017 – SEED TREATER 2.13. Towing the Seed Treater • Check with local authorities regarding transport on public roads. Obey all applicable laws and regulations. • Always travel at a safe speed, the seed treater can be transported up to a maximum of 60 mph (100 km/h) where permitted.

  • Page 13: Electric Motor Safety

    PROFESSIONAL SERIES – 2017 – SEED TREATER 2. SAFETY 2.14.2 Electric Motor Safety Power Source • Electric motors and controls shall be installed and serviced by a qualified electrician and must meet all local codes and standards. • Guards must be in place and secure. •...

  • Page 14: Tire Safety

    2. SAFETY PROFESSIONAL SERIES – 2017 – SEED TREATER 2.15. Tire Safety Failure to follow proper procedures when mounting a tire on a wheel or rim can produce an explosion that may result in serious injury or death. • DO NOT attempt to mount a tire unless you have the proper equipment and experience to do the job.

  • Page 15: Personal Protective Equipment

    PROFESSIONAL SERIES – 2017 – SEED TREATER 2. SAFETY 2.17. Personal Protective Equipment The following Personal Protective Equipment (PPE) should be worn when operating or maintaining the equipment. Safety Goggles • Wear safety goggles at all times to protect eyes from chemicals. Coveralls •...

  • Page 16: Safety Equipment

    2. SAFETY PROFESSIONAL SERIES – 2017 – SEED TREATER 2.18. Safety Equipment The following safety equipment should be kept on site: Fire Extinguisher • Provide a fire extinguisher for use in case of an accident. Store in a highly visible and accessible place.

  • Page 17: Safety Decal Locations And Details

    PROFESSIONAL SERIES – 2017 – SEED TREATER 2. SAFETY 2. Decide on the exact position before you remove the backing paper. 3. Align the decal over the specified area and carefully press the small portion with the exposed sticky backing in place.
  • Page 18 2. SAFETY PROFESSIONAL SERIES – 2017 – SEED TREATER Table 1. Safety Decals Part Number Description 9909–00021 DANGER ROTATING FLIGHTING HAZARD To prevent death or serious injury: • KEEP AWAY from rotating auger flighting. • DO NOT remove or modify auger flighting guards, doors, or covers.
  • Page 19 PROFESSIONAL SERIES – 2017 – SEED TREATER 2. SAFETY Table 1 Safety Decals (continued) Part Number Description P1513003 DANGER ELECTROCUTION HAZARD To prevent death or serious injury: • When operating or moving, keep equipment away from overhead power lines and devices. •...
  • Page 20 2. SAFETY PROFESSIONAL SERIES – 2017 – SEED TREATER Table 1 Safety Decals (continued) Part Number Description P1513001 WARNING To prevent serious injury or death: • Read and understand the manual before assembling, operating, or maintaining the equipment. • Only trained personnel may assemble, operate, or maintain the equipment.
  • Page 21 PROFESSIONAL SERIES – 2017 – SEED TREATER 2. SAFETY Table 1 Safety Decals (continued) Part Number Description 9909–00024 WARNING TRANSPORT HAZARD To prevent serious injury or death: • Securely attach equipment to vehicle with correct pin and safety chains. • Use a tow vehicle to move equipment. 9909–00023 WARNING BELT CRUSH HAZARD...
  • Page 22 2. SAFETY PROFESSIONAL SERIES – 2017 – SEED TREATER Table 1 Safety Decals (continued) Part Number Description 9909–00025 WARNING UPENDING HAZARD To prevent death or serious injury: • Anchor intake end and/or support discharge end to prevent upending. • Intake end must always have downward weight. Do not release until attached to tow bar or resting on ground.
  • Page 23 PROFESSIONAL SERIES – 2017 – SEED TREATER 2. SAFETY Table 1 Safety Decals (continued) Part Number Description 9909–00028 WARNING CRUSH HAZARD To prevent serious injury, engage cylinder lock before transporting. 9909–00027 WARNING CRUSH HAZARD To prevent serious injury, engage lock before clean out of hopper or transporting.
  • Page 24 2. SAFETY PROFESSIONAL SERIES – 2017 – SEED TREATER Table 1 Safety Decals (continued) Part Number Description 9909–00032 9909–00033 9909–00016 9909–00017 4400–90001...

  • Page 25: Features

    PROFESSIONAL SERIES – 2017 – SEED TREATER 3. FEATURES 3. Features This section covers the main features of the seed treater. 3.1. Figure 1. STORM Professional Seed Treater Table 2. STORM Professional Features Item Description Mixer Tube Transport Lock Controls Calibration and Treatment Pump Station Atomizing Chamber Conveyor...

  • Page 26: Controls

    3. FEATURES PROFESSIONAL SERIES – 2017 – SEED TREATER Table 2 STORM Professional Features (continued) Item Description Hopper Mixer Boot 3.2. Controls The STORM mixer section has the following controls: Mechanical Controls • Engine throttle with variable RPM. • Mover kit controls move/steer the unit. •...

  • Page 27: Preparation

    PROFESSIONAL SERIES – 2017 – SEED TREATER 4. PREPARATION 4. Preparation 4.1. Emergency Response Plan A response plan must be developed before using the seed treater the first time to be prepared in the event of an emergency. Keep a copy of the plan in the safety products storage box. This section provides guidance on developing your emergency response plan.

  • Page 28: Containment

    4. PREPARATION PROFESSIONAL SERIES – 2017 – SEED TREATER Explain the established procedures for the use and care of emergency and safety equipment including: • Personal Protective Equipment (PPE) • First aid kits • Eyewash stations • Fire extinguishers Explain procedures for: •...

  • Page 29: Transport

    PROFESSIONAL SERIES – 2017 – SEED TREATER 5. TRANSPORT 5. Transport Before continuing, ensure you have completely read and understood this manual’s Safety section, in addition to the safety information in the section(s) below. 5.1. Transport Safety • Check with local authorities regarding transport on public roads. Obey all applicable laws and regulations.
  • Page 30 5. TRANSPORT PROFESSIONAL SERIES – 2017 – SEED TREATER 5. Remove the pin and slide the hitch lock into the unlocked position on STORM Pro. 6. Use the conveyor intake control to lower the STORM Pro hitch onto the ball of the vehicle hitch. 7.
  • Page 31 PROFESSIONAL SERIES – 2017 – SEED TREATER 5. TRANSPORT Figure 3. Location of Transport Locks Table 4. Transport Locks Item Description Mixer Tube Transport Lock Conveyor Transport Lock Mixer Boot Transport Lock 4400–90001...
  • Page 32 5. TRANSPORT PROFESSIONAL SERIES – 2017 – SEED TREATER Figure 4. Correct Safety Cable Connection Figure 5. Transport Position 4400–90001...

  • Page 33: Placement

    PROFESSIONAL SERIES – 2017 – SEED TREATER 6. PLACEMENT 6. Placement Before continuing, ensure you have completely read and understood this manual’s Safety section, in addition to the safety information in the section(s) below. 6.1. Placement Safety • The seed treater is not insulated, keep away from overhead power lines. Electrocution can occur without direct contact.
  • Page 34 6. PLACEMENT PROFESSIONAL SERIES – 2017 – SEED TREATER • Manually adjust the atomizing chamber. • Adjust the position of the hopper, conveyor, and mixer boot until the atomizing chamber is in a vertical position. Important If the atomizing chamber cannot be positioned vertically, treatment quality will be affected. Treating is not recommended in this case.

  • Page 35: Operation

    PROFESSIONAL SERIES – 2017 – SEED TREATER 7. OPERATION 7. Operation Before continuing, ensure you have completely read and understood this manual’s Safety section, in addition to the safety information in the section(s) below. 7.1. Operation Safety • Keep away from rotating and moving parts, including the conveyor belt, auger flighting, drive components, shafts, and bearings.

  • Page 36: Treating Seed

    7. OPERATION PROFESSIONAL SERIES – 2017 – SEED TREATER It is normal for small chunks of rubber to separate from the intake seals during break-in. Ensure the belt is tracking in the center of the conveyor. Wing seals should contact the rubbers on both sides of the conveyor intake.

  • Page 37: Calibrate The Pumps

    PROFESSIONAL SERIES – 2017 – SEED TREATER 7. OPERATION 7.4.2 Calibrate the Pumps Calibrating the pumps enables the seed treater to provide the correct amount of treatment for the anticipated seed. Calibration requires the use of the calibration cylinders, treatment products, and the calibration control screens accessed via the touchscreen display.
  • Page 38 7. OPERATION PROFESSIONAL SERIES – 2017 – SEED TREATER 8. Choose to try again to hit 1000ml target or use resulted target. It will automatically adjust treating speed to match treatment application, and you can also accept an error in the case of a 2 pump calibration. 9.

  • Page 39: Operate The Treater & Treat Seed

    PROFESSIONAL SERIES – 2017 – SEED TREATER 7. OPERATION Item Description Quick Coupler Latches Calibration Valve 7.4.3 Operate the Treater & Treat Seed When operating the seed treater for the first time, the chemical hoses may be filled with antifreeze and will need to be flushed out.

  • Page 40: Emergency Stop

    7. OPERATION PROFESSIONAL SERIES – 2017 – SEED TREATER 1. Weigh the actual amount of seed that was treated. Note If you don’t know or are unable to determine the exact amount of seed that was treated, you can use the amount estimated on the screen. 2.

  • Page 41: Chemical Spill Cleanup

    PROFESSIONAL SERIES – 2017 – SEED TREATER 7. OPERATION 8. Connect the pump intake lines to a rinse water source and run the pumps backwards and forwards until lines are clear. Note Male couplers are included to allow for connection. 9.
  • Page 42 7. OPERATION PROFESSIONAL SERIES – 2017 – SEED TREATER 4. Touch up all paint nicks and scratches to prevent rusting. 5. Check tire pressure and inflate. For inflation pressure, refer to Section 11. – Specifications on page 6. Inspect the seed treater for cracks, tightness of fittings and fasteners, hydraulic hose cracks (if applicable). Have required repairs performed to replace worn or damaged components.

  • Page 43: Maintenance

    PROFESSIONAL SERIES – 2017 – SEED TREATER 8. MAINTENANCE 8. Maintenance Before continuing, ensure you have completely read and understood this manual’s Safety section, in addition to the safety information in the section(s) below. 8.1. Maintenance Safety • Keep components in good condition. Follow the maintenance procedures.
  • Page 44 8. MAINTENANCE PROFESSIONAL SERIES – 2017 – SEED TREATER Item Pre- Dai- Weekly Yearly Sea- Weeks quired end of Sea- son) Section 8.3 – Visually Inspect the Seed Treater on page 45 Section 8.14 – Check and Replace the Pump’s Chemical Hoses on page 51 Section 8.12 –...

  • Page 45: Visually Inspect The Seed Treater

    PROFESSIONAL SERIES – 2017 – SEED TREATER 8. MAINTENANCE 8.3. Visually Inspect the Seed Treater Lock out power before inspecting. Check the following during a visual inspection: 1. Ensure all guards are in place and in good working order. 2. Examine the seed treater for damage or unusual wear. 3.

  • Page 46: Oil The Chain Coupler

    8. MAINTENANCE PROFESSIONAL SERIES – 2017 – SEED TREATER 8.5. Oil the Chain Coupler The chain coupler is located between the hydraulic motor and the conveyor’s drive roller. Figure 10. Chain Coupler Location 8.6. Clean the Atomizer and Chemical Hoses After operating the seed treater, thoroughly clean the system to ensure efficient operation for the next treating application.
  • Page 47 PROFESSIONAL SERIES – 2017 – SEED TREATER 8. MAINTENANCE Figure 11. Clean-Out Position 4400–90001...

  • Page 48: Check The Chemical Pump Rollers

    8. MAINTENANCE PROFESSIONAL SERIES – 2017 – SEED TREATER 8.7. Check the Chemical Pump Rollers 1. Open the covers and confirm the pump rollers move freely. Figure 12. Chemical Pump Rollers 8.8. Clean the Filter Strainers 1. Unscrew the cap and rinse residue from strainer and replace. Replace the cartridge if it is damaged. Note Watch for the rubber seal that seals the cup to the body, it can get lost easily when cleaning.

  • Page 49: Fill The System With Antifreeze

    PROFESSIONAL SERIES – 2017 – SEED TREATER 8. MAINTENANCE 8.9. Fill the System with Antifreeze At the end of each treating season, fill the chemical hoses with antifreeze to keep them in good condition. Use the Flush Out function on the system maintenance screen. 1.

  • Page 50: Check And Maintain The Containment System

    8. MAINTENANCE PROFESSIONAL SERIES – 2017 – SEED TREATER Figure 14. Clean-Out Position 8.12. Check and Maintain the Containment System Chemical Hoses Ensure nothing is caught in the hoses, if there is, flush out with water or replace the line if necessary. Catch Containers Replace if these are worn or contain cracks/holes.

  • Page 51: Advanced Mixer Clean-Out

    PROFESSIONAL SERIES – 2017 – SEED TREATER 8. MAINTENANCE Figure 15. Mixer Boot Clean-out Door Seal 8.13. Advanced Mixer Clean-Out Complete this procedure daily or more often as required to keep the seed treater operating effectively. 1. Position the seed treater with the mover controls to allow for the full extraction of the mixer flighting with the mixer tube at a low angle, boot slightly raised, and conveyor intake at full height.

  • Page 52: Pump Tubing Break-In

    8. MAINTENANCE PROFESSIONAL SERIES – 2017 – SEED TREATER Note Use rubbing alcohol or soapy water to aid in getting hoses on. 8.14.1 Pump Tubing Break-In The pump tubing elements require a minimum 30 minute break-in period in order to meter consistently. If proper break-in is not performed, the system will not calibrate correctly.

  • Page 53: Tension The Conveyor Belt

    PROFESSIONAL SERIES – 2017 – SEED TREATER 8. MAINTENANCE Figure 16. Replacing a Conveyor Roller 8.16. Tension the Conveyor Belt Adjusting your conveyor belt for proper tension helps to ensure trouble-free operation and long belt life. Ensure the belt is thoroughly clean prior to tensioning or aligning the belt. Foreign materials may affect tension and alignment.

  • Page 54: Align The Conveyor Belt

    8. MAINTENANCE PROFESSIONAL SERIES – 2017 – SEED TREATER 7. If the conveyor belt is still loose after tensioning, the belt needs to be shortened or replaced (depending on wear). Figure 17. Conveyor Hopper Item Description Bearing Bolt and Nut Spout Roller Jam Nut Tightener Bolt...

  • Page 55: Adjust The Rollers

    PROFESSIONAL SERIES – 2017 – SEED TREATER 8. MAINTENANCE Figure 18. Roller out of Alignment Before Aligning the Belt: • The conveyor must be empty of all grain. • Wait until the belt makes a complete revolution before adjusting the rollers. Some belts may have uneven edges, appearing misaligned.

  • Page 56: Tension The Drive Belts

    8. MAINTENANCE PROFESSIONAL SERIES – 2017 – SEED TREATER Figure 20. Loosen the Bearing Nuts 2. Rotate adjustment bolt 1/2 turn. Figure 21. Rotate the Adjustment Bolt 3. Restart conveyor and run empty for 1 minute. 4. Stop the conveyor and remove ignition key or lock out the power source. 5.

  • Page 57: Align The Drive Belts

    PROFESSIONAL SERIES – 2017 – SEED TREATER 8. MAINTENANCE Figure 22. Typical Drive Belt Tensioning 1 inch (25 mm) 2. Tighten or loosen the drive belts (or idler pulley when equipped) to achieve the proper tension. Important The drive belt should be just tight enough to not slip on the drive pulley when operating. If the belt is too loose, it will slip, possibly causing a squeaking sound and slowing the belt down.

  • Page 58: Clean And Wash The Equipment

    8. MAINTENANCE PROFESSIONAL SERIES – 2017 – SEED TREATER 8.21. Clean and Wash the Equipment 1. Clean out excess grain from all areas of the seed treater. 2. Make sure water can drain from the seed treater tube and intake, then wash the tube with a water hose or pressure washer until all dirt, mud, debris, or residue is gone.
  • Page 59 PROFESSIONAL SERIES – 2017 – SEED TREATER 8. MAINTENANCE 7. Disconnect the old belt. 8. Reattach conveyor belt ends together. If required, use a ratchet strap clamped to both ends of belt to cinch belting ends together. Figure 23 on page Figure 23.

  • Page 60: Pinion Gear Adjustment

    8. MAINTENANCE PROFESSIONAL SERIES – 2017 – SEED TREATER Figure 24. Lacing the Conveyor Belt 8.25. Pinion Gear Adjustment When Equipped: The pinion gear should mesh with the ring gear to provide maximum tooth contact. If the pinion gear does not mesh entirely with the ring gear: 1.

  • Page 61: Change The Hydraulic Oil

    PROFESSIONAL SERIES – 2017 – SEED TREATER 8. MAINTENANCE 8.26. Change the Hydraulic Oil Change the hydraulic oil to remove any accumulation of dirt or condensation in the system. Do not over-fill the reservoir. Leave space to allow for level fluctuation. Refer to Section 11.

  • Page 62: Troubleshooting

    9. TROUBLESHOOTING PROFESSIONAL SERIES – 2017 – SEED TREATER 9. Troubleshooting Shut down and lock out all power sources before diagnosing any of the causes or attempting any of the solutions below. In the following section, we have listed some causes and solutions to some of the problems you may encounter.
  • Page 63 PROFESSIONAL SERIES – 2017 – SEED TREATER 9. TROUBLESHOOTING Pump won’t prime, Air leak on intake. Check treatment container connectors for pump output is correct fit, damage or manufacturing fluctuating problems. Check filter is tight and seal is installed. Check that the pump latches are engaged Pump shoe is not fully engaged.
  • Page 64 9. TROUBLESHOOTING PROFESSIONAL SERIES – 2017 – SEED TREATER increase product application rate by diluting in order to increase pump speeds or re-configure pump. Increase treating speed to increase pump speed if operating below 100%. Pump is operating too fast. Viscous (thick) products with high application rates, combined with high seed densities and high treating speeds...
  • Page 65 PROFESSIONAL SERIES – 2017 – SEED TREATER 9. TROUBLESHOOTING Atomizer not spinning. Seed coverage is poor Check connections or for damage to the atomizer. Atomizer basket or mixing Remove and clean components. chamber is plugged. Application rates are lower Consider increasing dilution of treating than 300 ml/100 kg of seed.
  • Page 66 9. TROUBLESHOOTING PROFESSIONAL SERIES – 2017 – SEED TREATER Inadequate hydraulic flow. Increase engine speed to increase hydraulic flow. Check condition of hydraulic oil and replace if necessary. Poor electrical connection to Check connections. differential valve. Conveyor out of adjustment An improperly adjusted conveyor can causing excessive drag.
  • Page 67 PROFESSIONAL SERIES – 2017 – SEED TREATER 9. TROUBLESHOOTING Flighting is worn. Repair or replace as required. Excessive noise or Flighting peeled back due to Inspect spout end of seed treater for vibration. plugging. flighting condition. Remove and replace *Remember to follow flighting sections as necessary.
  • Page 68 9. TROUBLESHOOTING PROFESSIONAL SERIES – 2017 – SEED TREATER Flighting is damaged. Repair or replace flighting. Worn bearing. Repair or replace bearing. Shear bolts fail Incorrect shear bolt type. Replace with correct part number. STORM shear bolts are specifically designed to repeatedly.
  • Page 69 PROFESSIONAL SERIES – 2017 – SEED TREATER 9. TROUBLESHOOTING Pump is worn out. Replace pump. Hydraulic cylinder Worn seal. Replace seal. leaking. Pinion gear slipping or Pinion gear not adjusted Adjust the pinion gear. See Pinion Gear binding. properly. Adjustment. Drive Cause Problem...

  • Page 70: Appendix

    10. APPENDIX PROFESSIONAL SERIES – 2017 – SEED TREATER 10. Appendix 10.1. Test Weight Procedure Follow this procedure to achieve highly accurate seed density and highly accurate seed treatment application. Repeat this procedure five times for best accuracy. Eliminate the highest and lowest value and average the three middle measurements for best results.

  • Page 71: Updating System Software

    PROFESSIONAL SERIES – 2017 – SEED TREATER 10. APPENDIX Figure 26. Test Weight Procedure Steps 10.2. Updating System Software To Ensure your STORM is operating at optimum levels, always install the most up-to-date software found on the "Downloading Software" tab. The STORM control uses a USB Flash Drive to transfer treating history and to install new software.

  • Page 72: Treating History & Job Information

    10. APPENDIX PROFESSIONAL SERIES – 2017 – SEED TREATER 10.2.1 Treating History & Job Information Important Installing new software will erase all treating history and job information stored in the controls. This step does not apply to new users who have not set up a treating history. Before Updating the Software 1.
  • Page 73 PROFESSIONAL SERIES – 2017 – SEED TREATER 10. APPENDIX 2. Once you have located the USB, insert it the USB port on your computer. The flash drive may appear on your desktop as removable drive. 3. If you have both the STORM FX and STORM PRO, please make sure you downloading the correct files for the model you will be updating.
  • Page 74 11. SPECIFICATIONS PROFESSIONAL SERIES – 2017 – SEED TREATER 11. Specifications CAPACITY Seed Flow 22.5 to 45 bu/min with 60 lb/bu Treatment Application Rate 10 to 1200 ml/100kg Treatment Application Coverage Accuracy +/- 5% (typical) Tube Size of Mixer 10” (254 mm) DIMENSIONS Transport Length 49’...
  • Page 75 Company, or to our factory, with transportation charges prepaid. This warranty does not obligate AGI to bear the cost of labor in replacing defective parts. Any defects must be reported to the Company before the end of the one year period.
  • Page 76 Shipping: 201 Industrial Drive, Swift Current, Saskatchewan S9H 5R4, CANADA Mailing: Box 1750, Swift Current, Saskatchewan S9H 4J8, CANADA Toll-Free: (877) 667-7421 (Canada & USA) Phone: (306) 773-7779 Fax: (306) 778-2524 Web: www.stormtreaters.com ©Ag Growth International Inc. 2020 Printed in Canada If you have any comments or questions on this manual, or find an error, email us at comments@aggrowth.com.

Table of Contents