Table of Contents
Advertisement
Available languages
Available languages
2.4.2
Description of the machine and its parts
Tedder and rake
OP-115
steering chassis, consisting of a wheel arm
height-adjustable, the height is locked by tightening the locking handle
V-belts, which are connected at regular intervals by crossbars
interconnected by a strut
10
on the front of the working mechanism. On the left side of the tedder there is a windrow shield
fodder. The distance of the shield from the machine is adjusted by sliding the windrow shield in the holder
the tightening element
15
. The support leg
gearbox.
To connect the
OP-115 OP-145 OP-115R
which also serves to tension the drive V-belt
The connection frame
2b
2.5
Operating Instructions
If the operating instructions contain "left side" or "right side", a view from the position of the operator standing behind
the steering handles of the propulsion unit is always meant
2.5.1
Machine Assembly
Ask your dealer to unpack the machine, assemble it and instruct you as part of the pre-sales service.
The assembly of the machine is solved by a separate manual.
2.5.1.1
Connection to gearbox DSK-316.1 - OP-115/145
The device may only be connected to the gearbox when the engine is turned off
Connecting the drive unit - see operating instructions for the drive unit
Also follow the operating instructions for the respective gearbox. The machine is designed to be driven by gearboxes with
switchable drive series DSK-316.1.
As per Fig.2 : Attach the plough to the gearbox on level and solid ground only. Adjust the tedder support leg so that the connecting
flange on the tedder
1
and the sleeve on the gearbox
forward so that the connecting flange slides into the sleeve and fold down lever
flange. Slide the support leg
2.5.1.2
Connection to the carrier RAPTOR Hydro – ROP-115
The device may only be connected to the multifunction carrier when the engine is turned off.
Also follow the operating instructions for the multifunction carrier.
As per Fig.4 : Attach the plough to the gearbox on level and solid ground only. Adjust the tedder support leg so that the connecting
frame on the tedder is horizontal. Loosen the M10x20
turns. Loosen the plastic wing nut
tensioning pulley of the adaptor V-belt
arms snap under the screws 1 in the rear brackets. Screw the M10x20 bolts with pin
2
. Reach into the area under the engine by hand and thread the V-belt 5 into the groove of the pulley 6 on the multifunction carrier.
Start to attach the V-belt always on the left side (i.e. tensioning pulley side). Check visually or by touch the correct fitting of the V-belt into
the pulley groove. Press on the plastic butterfly nut and slide the tensioning pulley inside until the nut fits into the groove in the side of the
frame moulding. Slide the pulley back to the end of the groove. Now firmly tighten the plastic butterfly nut.
2.5.1.3
Connection to the small tractor RAPID REX - OP-115R
The device may only be connected to the gearbox when the engine is turned off
Also follow the operating instructions for the use of the RAPID REX small tractor.
As per Fig.3 : Attach the plough to the gearbox on level and solid ground only. Adjust the tedder support leg so that the connecting
flange on the tedder
1
and the sleeve on the gearbox
so that it aims up. Move the small tractor forward so that the connecting flange of the tedder slides into the sleeve. Flip the locking lever on
the gearbox drive sleeve to the right so that it aims down. The locking pin must snap into the oval hole of the connecting flange of the
tedder. Slide the support leg
18
OP-145
OP-115R
ROP-115, Fig.1, consists of a frame
3
, a wheel leg
. The rake belt moves on two pairs of pulleys
16
is used to park the machine in a stable position and to facilitate connection to the
tedder with the gearbox, there is a connecting flange
17
.
is used to connect the
ROP-115
2
4
to the highest position and secure with the locking handle 5.
1
3
on the left side of the adapter by 2-3 turns. By pulling forward towards you you will discharge the
4
. Slide the multifunction carrier between the arms of the connecting frame until the grooves in the
2
4
to the highest position and secure with the locking handle
4
and a wheel fork with a wheel
6
. The working device has a transverse rake belt
8
with screwed rakes
11
in the machine frame. The machine has a metal cover
tedder with the
RAPTOR Hydro
are in one axis. Lift lever
3
3
- the pin must snap into the oval hole in the connecting
screws in the rear brackets on the frame of the multifunctional carrier by 2-3
2
are in one axis. Flip the locking lever
OP-115 OP-145 OP-115R ROP-115
1
, which is mounted on a two-wheel self-
5
. The travelling wheels are independently
9
. The crossbars are mounted in bearings and
13
, which allows windrowing of dried
14
and securing it by means of
2a
in the middle of the frame,
carrier,
on the gearbox sleeve upwards, move the gearbox
into the front brackets. Tighten the screws
3
on the gearbox drive sleeve to the right
5
.
7
formed by two
12
1
and
Advertisement
Chapters
Table of Contents
