Columbus McKinnon CM 622 Series Operating, Maintenance & Parts Manual

Columbus McKinnon CM 622 Series Operating, Maintenance & Parts Manual

Hand operated chain hoist

Advertisement

Quick Links

Note: When ordering parts, always furnish rated load and serial number of hoist on
which the parts are to be used.
For the location of the nearest CM Master Parts Depot, see the list located on the
inside front cover.
LIMITATION OF WARRANTIES, REMEDIES AND DAMAGES
THE WARRANTY STATED BELOW IS GIVEN IN PLACE OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
OR OTHERWISE, NO PROMISE OR AFFIRMATION OF FACT
MADE BY ANY AGENT OR REPRESENTATIVE OF SELLER
SHALL CONSTITUTE A WARRANTY BY SELLER OR GIVE RISE
TO ANY LIABILITY OR OBLIGATION.
Seller warrants that on the date of delivery to carrier the goods
are free from defects in workmanship and materials.
SELLER'S SOLE OBLIGATION IN THE EVENT OF BREACH OF
WARRANTY OR CONTRACT OR FOR NEGLIGENCE OR
OTHERWISE WITH RESPECT TO GOODS SOLD SHALL BE
EXCLUSIVELY LIMITED TO REPAIR OR REPLACEMENT, F.O.B.
SELLER'S POINT OF SHIPMENT, OF ANY PARTS WHICH
SELLER DETERMINES TO HAVE BEEN DEFECTIVE or if Seller
determines that such repair or replacement is not feasible, to a
refund of the purchase price upon return of the goods to Seller.
Any action against Seller for breach of warranty, negligence or
otherwise, must be commenced within one year after such
cause of action occurs.
NO CLAIM AGAINST SELLER FOR ANY DEFECT IN THE
GOODS SHALL BE VALID OR ENFORCEABLE UNLESS
BUYER'S WRITTEN NOTICE THEREOF IS RECEIVED BY
SELLER WITHIN ONE YEAR FROM THE DATE OF SHIPMENT.
Seller shall not be liable for any damage, injury or loss arising
out of the use of the goods if, prior to such damage, injury or
loss, such goods are (1) damaged or misused following Seller's
delivery to carrier; (2) not maintained, inspected, or used in
compliance with applicable law and Seller's written
instructions and recommendations; or (3) installed, repaired,
Columbus McKinnon Corporation • Industrial Products Division • 140 John James Audubon Parkway
Amherst, New York 14228-1197 • 1-800-888-0985 • Fax 716-689-5644
© 1996 Columbus McKinnon Corp.
altered or modified without compliance with such law,
instructions or recommendations.
UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES AS THOSE
TERMS ARE DEFINED IN SECTION 2-715 OF THE UNIFORM
COMMERCIAL CODE.
INDEMNIFICATION AND SAFE OPERATION
Buyer shall comply with and require its employees to comply
with directions set forth in instructions and manuals furnished
by Seller and shall use and require its employees to follow
such instructions and manuals and to use reasonable care in
the use and maintenance of the goods. Buyer shall not remove
or permit anyone to remove any warning or instruction signs
on the goods. In the event of personal injury or damage to
property or business arising from the use of the goods, Buyer
shall within 48 hours thereafter give Seller written notice of
such injury or damage. Buyer shall cooperate with Seller in
investigating any such injury or damage and in the defense of
any claims arising therefrom.
If Buyer fails to comply with this section or if any injury or
damage is caused, in whole or in part, by Buyer's failure to
comply with applicable federal or state safety requirements,
Buyer shall indemnify and hold Seller harmless against any
claims, loss or expense for injury or damage arising from the
use of the goods.
®
Printed in USA
SS 1/00
O P E R AT I N G ,
M A I N T E N A N C E &
PA R T S M A N U A L
H A N D O P E R AT E D
C H A I N H O I S T
®
SERIES 622
Before installing hoist, fill in the
information below.
Rated Load __________________
Serial No. ____________________
Purchase Date _______________
22950
S
O
L
U
T
I
O
N
Rated Loads:
1/2, 1, 2, 3, 5 and 10 tons
(500,1000, 2000, 3000, 5000,
and 10,000kg.)
Follow all instructions and warnings for
inspecting, maintaining and operating this hoist.
The use of any hoist presents some risk of personal
injury or property damage. That risk is greatly
increased if proper instructions and warnings are not
followed. Before using this hoist, each operator
should become thoroughly familiar with all warnings,
instructions and recommendations in this manual.
Retain this manual for future reference and use.
Forward this manual to operator.
Failure to operate equipment as directed
in manual may cause injury.
Price: $5.00
Manual No. B622-B
S

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CM 622 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Columbus McKinnon CM 622 Series

  • Page 1 Retain this manual for future reference and use. Serial No. ____________________ Forward this manual to operator. Columbus McKinnon Corporation • Industrial Products Division • 140 John James Audubon Parkway Failure to operate equipment as directed Purchase Date _______________ Amherst, New York 14228-1197 • 1-800-888-0985 • Fax 716-689-5644 in manual may cause injury.
  • Page 2 310 West 20th Street ALABAMA Kansas City, MO 64108 ABB POWER SERVICES 816/471-2610 ALBERTA 612 32nd Street, South Fax 816/421-3054 **COLUMBUS McKINNON, LTD. Birmingham, AL 35233 10311-174th Street 205/328-5952 NEW JERSEY Edmonton, Alberta T8H 1N3 Fax 205/251-6759 LIVELY AND COMPANY...
  • Page 4: Safety Precautions

    THE EQUIPMENT BEFORE ATTEMPTING TO OPERATE YOUR SERIES 622 HOIST. Consult Columbus McKinnon Corporation for any usage of Series 622 Hoists that do not involve raising of the load on the lower hook, or usage of Series 622 Hoists in the inverted position. Using hoists, without special precautions, in such applications may cause an accident that could result in injury and/or property damage.
  • Page 5: General Information

    All Columbus McKinnon (CM) Series 622 Hoists are inspected and performance test- ed prior to shipment. If any properly maintained hoist develops a performance prob- 2.
  • Page 6: Hook Inspection

    h. Hooks — dye penetrant, magnetic particle or other suitable crack-detecting inspections should be performed at least once a year, if external conditions WARNING indicate there has been unusual usage. Any deficiencies noted are to be corrected before the hoist is returned to service. Power operation may result in structural damage or premature wear that may Also, the external conditions may show the need for more detailed inspection which, cause a part to break and allow the load to fall.
  • Page 7: Hand Chain

    No. of Max. Length Links Allowable for Chain Stock Hoist WARNING Used Chain Diameter Rated Load In. (mm) Gage In. (mm) Tons (Kg.) Used motor oils contain unknown carcinogenic materials. 7.031 (178.6) 0.197 (5) ⁄ (500) 8.531 (216.7) 0.236 (6) 1 (1000) 14.125 (358.7) TO AVOID HEALTH PROBLEMS:...
  • Page 8 through the last link of the chain. Slide the loose end pin into hole in the handwheel side 2. The latch is secured to the hook (upper and lower) by a rivet. To plate (622-4). until the cotter pin hole is visible. Secure the loose end pin by reinstalling remove the latch, it is necessary to remove the head of the rivet by the cotter pin and spreading the legs of the cotter pin.
  • Page 9: Ordering Information

    ORDERING INFORMATION DEAD LOOSE BLOCK LOOSE The following information must accompany all correspondence or repair parts orders. Hoist Capacity Serial Number -- stamped on the capacity label. DEAD For parts orders also specify: BLOCK Quantity desired Key Number of Part Part Name Part Number When ordering replacement parts, consideration should be given to the need to...
  • Page 10 SERIES 622 HAND HOIST PARTS LIST PART NUMBER REQ’D PART NUMBER Rated Load—Tons (Kg.) 3 (3000) 5 (5000) 10 (10000) 1/2 (500) 1 (1000) 2 (2000) 622-1 Handwheel Cover with Studs 22910 22791 22812 Handwheel 22911 22792 22813 622-2 Brake Set (2 Friction Washers, Ratchet 622-3 22912 22793...
  • Page 11 622-40, 10 Ton Hoist Hanger Assembly. Except for Latch Kit, Hoist Hanger Kit and Dead End Kit, individual parts are 622-19 not available for repairs. NOTE: Metric Tools Required for Fasteners. 622-24 622-7 622-36 622-36 622-6 622-20 622-9 622-8 622-17 622-10 622-19 622-38...

Table of Contents