Advertisement
Quick Links
Advertisement
Related Manuals for McLelland MAP-1200EW
Summary of Contents for McLelland MAP-1200EW
- Page 1 6 SOURCE/6 Z0NE MAP-1200EW MULTIROOM CONTROLLER/ AMPLIFIER OWNERS MANUAL...
- Page 3 It provides up to 25W @ 8 Ohm Power by Class D amplifier to up to 18 zones which at can be controlled by packaged keypads (included with MAP-1200EW unit), RS232,IR or network. Overall the distribution systems easy-to- install, so every audiophile can enjoy the powerful audio wherever they are.
- Page 5 1. Power ON/OFF Switch 2. Status LED White: Zone ON Blue: Standby mode Blue/White: Mute 14 15 Integrated network...
- Page 8 MAP-1200EW MAP-1200EW 3.5mm Stereo...
- Page 9 4-8 Ohm. There are 9 two MAP-1200EW modes that can be set for different setups: Stereo or Bridge. An 8 Ohm speaker can only be used when in Bridge mode. To choose between modes,...
- Page 10 6 POE enabled keypads. This allows for source MAP-1200EW control from each specific zone as well as IR routing to the appropriate source devices once selected. The also comes with a hub that allows for MAP-1200EW all 6-keypads to be connected to the amp via Cat5e/6.
- Page 11 FRONT BACK MAP-1200EW...
- Page 13 When being used with keypads, the can receive IR signals from MAP-1200EW each zone, and routed back through the Cat5e/6 and Keypad up to the Amplifier to control the selected source. For example, if Source 2-DVD is selected in Zone 1, the user will be able to control the DVD player to power the device on/off, change settings ect.
- Page 14 Master SLAVE 1 SLAVE 2 INTEGRATED NETWORK Set the switch to Ethernet. Connect the Cat5 cable to Ethernet port and LAN port of the Router.
-
Page 15: Ethernet Connection
In case wireless connection is needed to use for the installation, please follow the below steps to setup the Wi-Fi connection: 1.Power on MAP-1200EW and make sure the amplifier is not out of Wi-Fi range of router. 2.Using PC, Smart phone or Tablet (PC is recommended), searching the Wi-Fi connection and find out the Wi-Fi signal from this amplifier. - Page 16 6.After the restart, “AP Client” will show on the webpage. Click “AP Client” and select the local network which you want to connect. Then click “Apply”, the router will restart.
- Page 17 Set the switch to Ethernet. Connect the Cat5 cable to Ethernet port and LAN port of the Router. Two ways to find the IP address of MAP-1200EW 1.Open the IE web browser of PC, log in to the WEB configuration page of local...
- Page 18 2. Using “Advanced_IP_Scanner” software to find the IP address. Please visit www.advanced-ip-scanner.com for free download. Then enter the IP address of MAP-1200EW to the IE browser (shown as below), ensure the Serial Configure is 9600,n,8,1. After finishing this step, MAP-1200EW...
- Page 19 Download free software “PuTTY” Tool from the internet to control the device. Operation diagram as below:...
- Page 20 Click Telnet, enter the IP address of MAP-1200EW and port: 8080. Click Open. When the IP address connected, the operation diagram shows as below: Key in the command code to control MAP-1200EW. For the detail of command codes, please find the RS-232 command codes in this...
- Page 21 RS-232 communication with third party automation systems. All keypad and remote control operations can be controlled via RS-232 in addition to system expansion up to 18 zones or 3 MAP-1200EW units linked together using the included 18 pin expansion cable.
- Page 22 Click Open. Note: To find the information for the COM port, please open the device manager of the computer, shown as below: When the IP address connected, the operation diagram shows as below: Key in the command code to control MAP-1200EW.
- Page 23 MAP-1200EW RS-232 CONTROL CODES (Baud Rate: 9600,8,N,1 , DB9 Connector Pin out, Tx, Rx, GND) 'CR':Carriage Return (0x0D) Not case sensitive Control Command Structure <xxPPuu'CR' Reply Control Command Structure >xxPPuu'CR' xx: Represent control command code 10 :All zones of host computer 1...
- Page 24 30 :All Zones of host computer 3 11 :Zone1 of host computer1 12 :Zone2 of host computer1 13 : Zone3 of host computer1 21 : Zone1 of host computer2 22 : Zone2 of host computer2 23 : Zone3 of host computer2 ....
- Page 25 BL:Balance Control CH:Source Control LS: The connection status of line control Reply command: >xxPPuu'CR' Enter1<********'CR' Change Source 1 display name;********It must be 8 effective ASCII code Enter2<********'CR' Change Source 2 display name Enter 3<********'CR' Change Source 3 display name Enter 4<********'CR' Change Source 4 display name Enter 5<********'CR' Change Source 5 display name Enter 6<********'CR' Change Source 6 display name Enter M<********'CR' Change display name of connect control when it starts...
- Page 26 EXAMPLES OF RS-232 COMMAND CODE All Zone ON <10PR01 Zone 1 ON <11PR01 All Zone OFF <10PR00 <21PR00 Salve 1 / Zone 1 OFF All Zone Mute ON <10MU01 <16MU01 Zone 6 Mute ON All Zone Mute OFF <10MU00 <35MU00 Salve 2 / Zone 5 Mute OFF All Zone Source 01 <10CH01...
- Page 27 REPLY COMMAND >xxaabbccddeeffgghhiijj xx: Unit / Zone >1100000000200707100100 aa: PA IN Status bb: Power Status cc: Mute Status dd: DT Status ee: Volume Status ff: Treble Status gg: Bass Status hh: Balance Status ii: Source Status jj: Keypad Connection Status (00: Unconnected, 01: Connected)
- Page 28 APP QUICK START Download the control APP: 1. The control APP is available for Apple iPhone/iPad and Android smart phone/Pad, 2. Please search “MAP-800/1200” on Google Play / App Store to download. 3. Download and install the APP Note. This APP is applied to McLLELLAND controller and Multi-Room amplifiers...
- Page 29 APP QUICK START – FUNCTION INSTRUCTION 1. Output Zone Selection (Press and hold the button to change the zone name) 2. Input Source Selection Press and select the input source. The name of input source could be changed. 3. Treble/Bass/Balance 4.
- Page 30 APP QUICK START – SETTINGS AND CONNECTION 1. Mobile phone IP address When the smart phone or Pad is connected to local network, the IP will automatically show on this area. 2. AUTO Press AUTO to search the device IP. 3.