Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Raycus RFL-QCW450/1500FS
Summary of Contents for Raycus RFL-QCW450/1500FS
- Page 1 RFL-QCW450/1500FS User manual Wuhan Raycus Fiber Laser Technologies Co., Ltd.
-
Page 2: Table Of Contents
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 Content 1 Safety Information........................1 Symbols Used in this User Guide.................. 1 Laser Classification......................1 Safety Labels........................2 Optical Safety.........................3 Electrical Safety......................3 Other Safety Rules......................4 2 Product Description........................4 Features.......................... 4 Package Contents......................4 Unpacking and Inspection....................5... -
Page 3: Safety Information
User manual QCW450/1500 1 Safety Information Thank you for choosing Raycus fiber laser. This User Guide provides important safety, operation, warranty and other information. Please read it carefully before you use this product. In order to ensure safe operation and optimal performance of the product, please follow the warnings, cautions, operating procedures and other instructions accordingly. -
Page 4: Safety Labels
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 WARNING: You must use appropriate laser safety eyewear when operating this device. The laser safety eyewear is selected according to the range of wavelengths emitted from this product. The end user must ensure that the laser safety eyewear used protects against light emitted by the device over its entire range of wavelengths. -
Page 5: Optical Safety
If the fuse blows out, replace it with only the same types and ratings. The use of other fuses or material is prohibited. You can contact Raycus for the information of the fuse. -
Page 6: Other Safety Rules
4) Do not remove the covers of the laser, or the warranty will be void. All maintenance must be performed in Raycus or by qualified Raycus personnel. 2 Product Description 2.1 Features... -
Page 7: Unpacking And Inspection
User manual QCW450/1500 Unpacking and Inspection Your Raycus QCW fiber laser is shipped in a package designed to provide maximum protection. Upon delivery, please inspect all packaging for evidence of mishandling or damage. If you find any evidence of mishandling, please save the damaged material and contact the shipping agent and Raycus immediately. -
Page 8: Precautions For Use
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 personnel. In order to prevent electric shock, please do not break the seal or uncover the shield. Failure to comply with this instruction will void the warranty; 3) Please check the fiber connector carefully to prevent dust or other pollution. -
Page 9: Installation
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 Pulse width(ms) 0.1-75 Rated output power Maximum pulse energy Rated output power Wavelength (nm) 1080±5 Rated output power Rated output power; Working duration: ≥ Output power instability 6hrs; ±1.5% Working temperature: 25℃... - Page 10 Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 Figure 2 Front panel view (unit: mm) Figure 3 Rear panel view (unit: mm)
-
Page 11: Dimensions And Installation Of Fiber Connector
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 Figure 4 Top and Side view (unit: mm) 3.2 Dimensions and installation of fiber connector Figure 5 shows the dimensions of the fiber connector. Figure 5 RFL-QBH Fiber Connector (mm) CAUTION: ... -
Page 12: Cooling Requirements
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 3.3 Cooling Requirements Table 4 Cooling Requirements Parameters Unit values Cooling capacity >1800 Minimum flow L/min Maximum input pressure Water pipe size 10（PU quick plug water pipe） 1) Water temperature setting：... -
Page 13: Installation Procedure
5) Please check the laser fiber connector and clean it as necessary before installing it into the process optics. If dust is found on the output cable, please contact Raycus in time, and do not continue to install and operate the laser for the time being. -
Page 14: Using The Product
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 use electric fan to dissipate heat when it is hot every day in summer, so as to avoid large dust in the air). 9) The minimum bending radius of the fiber should not be less than 20cm under non-working conditions such as transportation and storage. -
Page 15: Rear Panel
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 1. REM/OFF/ON: Key switch, the power switch of the laser. Insert the key; either turn the key clockwise to the 'ON' position or counterclockwise to 'REM' position will power on the laser. -
Page 16: Power Connection
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 3. MOD: Modulation input, the BNC connector for switching the laser on and off in remote control modes. The control signal should be able to apply current over 10mA, and the voltage should be 24V. -
Page 17: Interface Definitions
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 The other end of the power cord is stripped off and each wire is crimped with a ‘pin-type cable connector’. There are three wires labeled L, N and PE, respectively. Connect the wires to the AC power supply according to the labels;... -
Page 18: Modulation Input
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 SERVICE port is a female DB25 connector. If the pins 6 and 7 are disconnected, the laser will stop emitting immediately and the Yellow alarm light will be on. After connecting pins 6 and 7 is, it is necessary to power on the laser again. -
Page 19: Control Interface
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 The core of the modulation signal cable is the positive, and the external metal mesh is the negative. Before the modulation signal is connected to the laser, please check whether its voltage meets the product requirements. -
Page 20: Software Operation
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 The pin definition of RS-232 cable is listed in Table 6 Table 7 Pin Definition of RS-232 Cable Definition Other pins are idle. the RS-232 serial port cable is also provided, as in Figure 15。... -
Page 21: Startup Settings
There are four working modes of the laser: internal CW mode, internal modulation mode, external CW mode and external modulation mode. Among them, the first two are internal modes, which are used for internal debugging of Raycus personnel, and can also be used for customer debugging; the latter two are external modes, which are provided to customers. - Page 22 Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 4.5.2.1 Internal CW Mode When internal CW mode is selected, the laser can emit continuously, the power can be set to 25% - 100% adjustable to adjust the output power of the laser.
- Page 23 Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 When either duty cycle mode or pulse width mode is selected, the other mode is locked, but another parameter will be calculated and displayed according to power and frequency, as shown in .
- Page 24 Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 external CW mode and 4.5.2.4 external modulation mode, the setting of pulse parameters shall meet the requirements of Figure 20, with two restrictions, namely: Pulse width and duty cycle VS peak power...
- Page 25 Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 (a ) power 100%，duty circle 40% b) frequency 10Hz, pulse width 0.5ms Figure 21 Parameter Setting Prompt Diagram When the pulse width mode is selected, in order to ensure that the output duty cycle is not less than 1% and not more than 75%, the above three conditions should be met at the same time.
-
Page 26: Common Faults
Wuhan Raycus Fiber Laser Technology Co., Ltd User manual QCW450/1500 4.6 Common Faults Some faults may occur in the process of using the laser. When the fault occurs, the alarm light on the front panel of the laser will be on, and the laser will stop emitting. -
Page 27: Warranty, Return And Maintenance
For all products repaired or replaced during the warranty period, only those with special problems are guaranteed free of charge. Raycus reserves the right to receive payment for the products with problems under normal use. -
Page 28: Technical Support And Product Maintenance
1) There are no parts built-in for user maintenance in this product, so all maintenance shall be carried out by Raycus technical personnel. 2) In case of any fault in the use of the product, the technical personnel of Raycus shall be informed in time and troubleshooting shall be carried out 3) All repair or replacement products must be placed in the original packaging box provided by Raycus.