Advertisement
Quick Links
NOTES:
• Ensure that both left and right hand Fender Flares suit the profile of the vehicle. Note the areas where the Fender Flares come
in contact with the vehicle.
• Before fitting Fender Flares remove any mouldings, strips or existing flares from the wheel arch. If there is a body side moulding,
mark where the moulding is to be cut, alternatively the Fender Flares can be cut to go around the moulding. Be sure to allow
enough room for the extrusion.
• Read instructions carefully. This product must be installed exactly as specified in these instructions.
Failure to do so may result in improper fit and/or retention.
TOOLS REQUIRED:
3
7
8
13
14
24/05/19
FENDER FLARES
INSTALLATION INSTRUCTIONS
FORD PX3 RANGER 2019MY-
• Short Phillips head Screwdriver
• Flat head Screwdriver
• Drill & 8mm & 10.5mm Drill Bit
• Steel Ruler
• Tin Snips
COMPONENTS LIST
1
2
5
6
9
10
15
16
17
NO.
1
4
2
3
4
5
6
7
8
9
10
11
12
11
12
13
14
15
18
19
16
17
18
19
• 7mm,8mm & 10mm Socket or Spanner
• Masking Tape
• Mild Soapy Water & Clean Cloths
• Felt Tip Marker
• Utility Knife
COMPONENT
Front LHS Fender Flare
Front RHS Fender Flare
Front LHS Bumper Flare
Front RHS Bumper Flare
Rear LHS Fender Flare
Rear RHS Fender Flare
Screw 25mm
Speed Clip 8.5mm hole centre
Speed Clip 11mm hole centre
Phillips Head Screw
Alcohol Wipe
6mm Plastic Scrivet
Rust Inhibitor
10mm Plastic Scrivet
5mm Spacer
Sensor Blanking Molding LHS
Sensor Blanking Molding RHS
Star Washer
Blanking Plate
FF935
QTY
1
1
1
1
1
1
20
12
4
2
4
16
1
4
4
1
1
2
2
Page 1 of 7
Advertisement
Related Manuals for EGR FF935
Summary of Contents for EGR FF935
- Page 1 FF935 FENDER FLARES INSTALLATION INSTRUCTIONS FORD PX3 RANGER 2019MY- NOTES: • Ensure that both left and right hand Fender Flares suit the profile of the vehicle. Note the areas where the Fender Flares come in contact with the vehicle. • Before fitting Fender Flares remove any mouldings, strips or existing flares from the wheel arch. If there is a body side moulding, mark where the moulding is to be cut, alternatively the Fender Flares can be cut to go around the moulding.
- Page 2 FF935 FENDER FLARES INSTALLATION INSTRUCTIONS MUD FLAP (x7) Remove the mud flaps by removing the (7) scrivets from Wash the areas of contact on the vehicle and wipe dry. inside the wheel arch as shown. Wipe the fender where the flare will contact, using provided Alcohol wipes.
- Page 3 FF935 FENDER FLARES INSTALLATION INSTRUCTIONS FRONT-RHS MUD FLAP 38mm REMOVE MATERIAL 51mm 44mm FRONT-LEFT FRONT-RIGHT Prepare the Front Mud Flaps by cleaning them & covering Measure and mark Mud Flap area to be removed, as the marked areas with masking tape.
-
Page 4: Section View
FF935 FENDER FLARES INSTALLATION INSTRUCTIONS VIEW INSIDE THE FENDER DRIVING LIGHT HOUSING DISLODGE CLIP Follow the wiring harness that supports Active park assist Pull extra harness length gently through the OEM hole in sensor up to the edge clip located under the driving lamp the bumper &... - Page 5 FF935 FENDER FLARES INSTALLATION INSTRUCTIONS Fit the bumper flare to the vehicle as shown. Secure the flare using previously removed screw and scrivet as shown. FOR THE LHS FRONT FENDER FLARE INSTALLATION REPEAT STEPS 1 TO 21 Ensure that flares are aligned. Remove the tape liner.
- Page 6 FF935 FENDER FLARES INSTALLATION INSTRUCTIONS (x1) (x3) (x2) (x1) MUD FLAP LHS SHOWN LHS SHOWN Remove the rear mud flaps by removing and retaining the Remove the (3) scrivets from inside the rear wheel arch (2) screws and (2) scrivets from inside the wheel arch as shown.
- Page 7 FF935 FENDER FLARES INSTALLATION INSTRUCTIONS FENDER SPEED NUT LHS SHOWN LHS SHOWN Attach the rear part of the rear fender flare with (3) Hex Attach the front part of the rear fender flare with (3) Hex head screws and factory plastic nuts. Secure the rear lower head screws and Speed nuts as per front fender process.