U-Line H-161 Manual

U-Line H-161 Manual

Impulse poly bag sealers
Hide thumbs Also See for H-161:

Advertisement

Available languages

Available languages

H-161, H-163, H-190
H-293, H-306, H-458
H-963, H-1029, H-1252
IMPULSE POLY BAG
SEALERS
OPERATING ISSUE
Sealer is not sealing.
Sealer light comes on but not sealing.
If the sealer is not sealing after being plugged in the
first time.
If the sealer stops sealing, but the sealing light still
comes on.
STEP 2
PAGE 1 OF 6

TROUBLESHOOTING

STEP 5
RECOMMENDATIONS
Adjust timer knob at end of sealer to higher setting.
Unplug unit. Remove metal plates and Teflon strip
to see if heating element needs to be replaced or
reattached.
The timer knob may be set too low.
1.
Check setting on timer knob at end of sealer (see
photo).
2.
With the unit plugged in, turn timer clockwise to
raise setting and test.
3.
Continue to adjust setting and test until desired
seal is achieved.
The heating element may need to be replaced.
1.
Unplug unit.
2.
Remove metal plates and teflon strip to reveal
heating element (see photo).
3.
Carefully remove screw that holds the black
plastic protective cover in place.
4.
Starting near the hinge, remove heating element
one end at a time by gently pulling tension rods.
5.
Pull new element from included kit and place it
over tension rods starting near hinge (see photo).
6.
Replace screw, teflon strip and metal plates. Plug
in unit to test.
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
0617 TH-161

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H-161 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for U-Line H-161

  • Page 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-161, H-163, H-190 H-293, H-306, H-458 H-963, H-1029, H-1252 IMPULSE POLY BAG SEALERS TROUBLESHOOTING OPERATING ISSUE RECOMMENDATIONS Sealer is not sealing. Adjust timer knob at end of sealer to higher setting.
  • Page 2 H-161, H-163, H-190 H-293, H-306, H-458 H-963, H-1029, H-1252 IMPULSE POLY BAG SEALERS TROUBLESHOOTING CONTINUED OPERATING ISSUE RECOMMENDATIONS If the sealer stops sealing and the sealing light does The arm may not be activating the microswitch. not come on. Unplug unit.
  • Page 3 H-161, H-163, H-190 π H-293, H-306, H-458 800-295-5510 H-963, H-1029, H-1252 uline.mx TERMOSELLADORAS DE IMPULSO PARA BOLSAS DE POLIETILENO SOLUCIÓN DE PROBLEMAS PROBLEMA DE FUNCIONAMIENTO RECOMENDACIONES La termoselladora no está sellando. Ajuste la perilla del temporizador de la termoselladora a un número más alto.
  • Page 4 H-161, H-163, H-190 π H-293, H-306, H-458 800-295-5510 H-963, H-1029, H-1252 uline.mx TERMOSELLADORAS DE IMPULSO PARA BOLSAS DE POLIETILENO CONTINUACIÓN DE SOLUCIÓN DE PROBLEMAS PROBLEMA DE FUNCIONAMIENTO RECOMENDACIONES Si la termoselladora deja de sellar y la El brazo quizá no está activando el microinterruptor.
  • Page 5 H-161, H-163, H-190 π H-293, H-306, H-458 1-800-295-5510 H-963, H-1029, H-1252 uline.ca SOUDEUSES À IMPULSION DE SACS DE POLYÉTHYLÈNE DÉPANNAGE PROBLÈME DE FONCTIONNEMENT RECOMMANDATIONS La soudeuse ne soude pas. Réglez le bouton de la minuterie à l'extrémité de la soudeuse sur un paramètre plus élevé.
  • Page 6 H-161, H-163, H-190 π H-293, H-306, H-458 1-800-295-5510 H-963, H-1029, H-1252 uline.ca SOUDEUSES À IMPULSION DE SACS DE POLYÉTHYLÈNE DÉPANNAGE SUITE PROBLÈME DE FONCTIONNEMENT RECOMMANDATIONS Si la soudeuse ne soude plus et le Le bras n'active peut-être pas le microrupteur.

This manual is also suitable for:

H-163H-190H-293H-306H-458H-963 ... Show all

Table of Contents