Related Manuals for Keysight N9010AK-MTU
Summary of Contents for Keysight N9010AK-MTU
- Page 1 Keysight Technologies N9010A EXA Signal Analyzer Option MTU, MultiTouch User Interface Upgrade Kit Option MTP, MultiTouch User Interface Upgrade Kit with PC7 CPU Installation Note...
- Page 2 The information contained in this document is subject to change without notice. Keysight Technologies makes no warranty of any kind with regard to this material, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
- Page 3 N9010AK-MTP - MultiTouch User Interface Upgrade with PC7 CPU The N9010AK-MTU should only be installed on N9010As that already have the PC6 or PC7 CPU. This kit includes a new SSD, to ensure that when a disk drive recovery is performed, the software version recovered will be new enough to recognize the MultiTouch front panel assembly.
- Page 4 Option MTU and MTP, MultiTouch User Interface Upgrade Kits Once this upgrade is performed, the analyzer will only recognize IMPORTANT measurement applications whose model number ends in a "C". For example, the N9068C, Phase Noise measurement application or the N9071C GSM/EDGE measurement application.
- Page 5 Option MTU and MTP, MultiTouch User Interface Upgrade Kits N9010AK-MTU, MultiTouch User Interface Upgrade Kit Parts List Quantity Description Keysight Part Number Front Frame Assembly, MultiTouch, Light Color N9020-60261 Trim Strip, Top, Benchtop, Light Color N9020-40017 Trim Strip, Top, Opt PRC, Light Color...
- Page 6 Option MTU and MTP, MultiTouch User Interface Upgrade Kits N9010AK-MTP, MultiTouch User Interface with PC7 CPU Upgrade Kit Parts List Quantity Description Keysight Part Number Front Frame Assembly, MultiTouch, Light Color N9020-60261 Trim Strip, Top, Benchtop, Light Color N9020-40017 Trim Strip, Top, Opt PRC, Light Color N9020-40019 Trim, Side, 177.0 H...
-
Page 7: Tools Required
Option MTU and MTP, MultiTouch User Interface Upgrade Kits Tools Required — T-10 TORX Driver — T-20 TORX Driver — 5/16-inch torque wrench — Deep 5/16-inch socket wrench — ¼-inch open-end wrench — Scissors or knife — Diagonal cutters — Microsoft Windows based personal computer with internet access and USB port —... -
Page 8: Installation Procedure
Option MTU and MTP, MultiTouch User Interface Upgrade Kits Installation Procedure Analyzer Information 1. Connect a power cord to the analyzer and turn on the analyzer. 2. After the analyzer has completed turning on, press System, Show, System. Make note of the following information from the Show System screen: Product Number: _____________ Serial Number: ______________... - Page 9 Option MTU and MTP, MultiTouch User Interface Upgrade Kits License Key Backup In order for the instrument being upgraded to keep the same option configuration that it had prior to the upgrade, it is mandatory that the licenses be transferred from the original disk drive to the new disk drive.
- Page 10 Option MTU and MTP, MultiTouch User Interface Upgrade Kits Backup Calibration Data There are three different backup procedures that might need to be followed. Which backup procedure to be run will depend on the software version that currently exists in the instrument being upgraded.
- Page 11 Option MTU and MTP, MultiTouch User Interface Upgrade Kits S/W Revision Greater Than or Equal To A.01.55 and Less Than A.02.00 1. Close the instrument application software by pressing File, Exit, Enter. 2. Connect a USB mouse to one of the instrument USB ports. 3.
- Page 12 Option MTU and MTP, MultiTouch User Interface Upgrade Kits S/W Revision Greater Than A.02.00 1. With the instrument turned on and the signal analyzer application running as normal, connect a USB mouse to one of the instrument USB ports. 2. Locate a USB storage device and insert it into one of the available instrument USB ports. (Perform a virus scan on this device before use) 3.
- Page 13 Option MTU and MTP, MultiTouch User Interface Upgrade Kits Replacing Solid State Drive (SSD) - N9010A-MTU Upgrade Only The steps in this section apply only to N9010A-MTU upgrades, where the solid state drive is replaced. If the N9010A-MTP upgrade is being performed, skip to" Replacing CPU Assembly - N9010A-MTP Upgrade Only".
- Page 14 Option MTU and MTP, MultiTouch User Interface Upgrade Kits 3. Refer to Figure 4. Remove the 4 machine screws (1) from the disk drive carrier assembly that secure the drive (2). Figure 4 Disk Drive Screws 4. Remove the disk drive (2) from the carrier assembly. 5.
- Page 15 Option MTU and MTP, MultiTouch User Interface Upgrade Kits Replacing CPU Assembly - N9010A-MTP Upgrade Only The steps in this section apply only to N9010A-MTP upgrades, where the CPU is replaced. If the N9010A-MTU upgrade is being performed, skip to "Replacing Solid State Drive (SSD) - N9010A-MTU Upgrade Only".
- Page 16 The instrument may require more than 5 minutes to power-on. This is affected by the operating system initial start-up requirements. 3. The Keysight Technologies screen appears followed by a screen that automatically loads the operating system. 4. The License Agreement dialog box as shown in...
- Page 17 Option MTU and MTP, MultiTouch User Interface Upgrade Kits Figure 6 License Agreement Dialog Box Select Agree to continue, or Do Not Agree to turn off the instrument before initializing the software. After launching the setup, do not turn off the instrument or remove power before the setup routine completes and the system restarts.
- Page 18 Option MTU and MTP, MultiTouch User Interface Upgrade Kits 6. The anti-virus notification as shown in Figure 8 will then appear. Figure 8 Anti-Virus Message If you do not check the "Do not show this message again" check box, this message will be displayed each time the instrument is turned on.
- Page 19 Option MTU and MTP, MultiTouch User Interface Upgrade Kits License Key Restore 1. Insert the USB storage device containing the backed-up license key. 2. Navigate to the "Licenses_.." folder on the USB storage device that is for the instrument being upgraded.
-
Page 20: Software Updates
2. If the original software version noted in step 2 of the Analyzer Information procedure is newer than the currently-installed software version, an instrument software update is required. The latest revision of the X-Series signal analyzer software may be downloaded from: http://www.keysight.com/find/xseries_software Installation Note N9010-90072... - Page 21 Option MTU and MTP, MultiTouch User Interface Upgrade Kits FPGA Code Update If the instrument software was updated in the previous section, it is not necessary to also do the FPGA Code Update; this update is performed as part of the instrument software update. If the instrument software was not updated, continue with the procedure below.
- Page 22 Option MTU and MTP, MultiTouch User Interface Upgrade Kits 5. To program the FPGA code enter 1 and press Enter. You will need to confirm this selection by selecting 1 and Enter one more time. 6. The programming of the FPGA code could take a few minutes to complete. Once it has finished the instrument will reboot itself to use the new code.
- Page 23 Option MTU and MTP, MultiTouch User Interface Upgrade Kits Data Restore 1. With the instrument turned on and the signal analyzer application running as normal, connect a USB mouse to one of the instrument USB ports. 2. Connect the USB memory device that was earlier used to backup the instrument calibration data to one of the instrument USB ports.
- Page 24 Option MTU and MTP, MultiTouch User Interface Upgrade Kits Calibration Data Backup to SD Card The PC7 processor assembly contains an internal SD card for the purpose of providing a location to back up the calibration data. After the PC7 assembly is installed and the calibration data from the previously installed processor assembly has been restored, another backup should be performed, this time to the SD card.
- Page 25 "Order 3571234, product N9082BL-1FP, has migration product N9082C-1FP. The license will be in a following email." d. Using the mouse and the Ctrl key on the keyboard, select all entries in the Keysight License Manager (KLM) that contain the model number of the ordered product (in the example above, this would be N9082B.
- Page 26 Successful License Installation Verify the License Installation 1. In Keysight License Manager, click on View and select Refresh (localhost). This will refresh the list of licenses installed. 2. Verify that licenses for the products listed in the second e-mail appear in the Product/Feature column.
-
Page 27: Analyzer Disassembly
Option MTU and MTP, MultiTouch User Interface Upgrade Kits Analyzer Disassembly If the instrument is placed on its face during any of the following procedures, be sure to use a soft surface or soft cloth to avoid damage to the front panel, keys, or input connector. If the analyzer has Option PRC, Portable Configuration, refer to the “Portable Instrument (Option PRC)”... - Page 28 Option MTU and MTP, MultiTouch User Interface Upgrade Kits Standard Instrument (Benchtop Configuration) 1. Disconnect the instrument from ac power. 2. Refer to Figure 14. Using the T-20 driver, remove the four screws (two on each side) (1) that attach the handle strap (2) on each side of the instrument. 3.
- Page 29 Option MTU and MTP, MultiTouch User Interface Upgrade Kits Portable Instrument (Option PRC) Make sure any adapters on the front panel are removed. 1. Disconnect the instrument from ac power. 2. Refer to Figure 15. Using the T-20 driver, remove the four screws (two on each side) (1) that hold the bail handle (2) to the front frame.
- Page 30 Option MTU and MTP, MultiTouch User Interface Upgrade Kits 5. Refer to Figure 16. Using the T-20 driver, remove the four screws including washers (1) that hold the rear bumpers (2) in place. 6. Pull the instrument cover (3) off towards the rear of the instrument. Figure 16 Option PRC Instrument Outer Case Removal Installation Note N9010-90072...
- Page 31 Option MTU and MTP, MultiTouch User Interface Upgrade Kits Front Frame Assembly Removal 1. If the EXA has Option EXM, External Mixer, use a ¼" open end wrench and 5/16" open end wrench to disconnect semi-rigid coax cable W27 from W28. 2.
- Page 32 Option MTU and MTP, MultiTouch User Interface Upgrade Kits 3. Refer to Figure 18. Pull the front frame carefully away from the chassis. Remove the ribbon cable W1 from the A8 Motherboard. W1 may have locking springs on each side. Depress the spring on each side of the connector to remove from the motherboard.
-
Page 33: Removal Of Option Exm, External Mixing Parts From Original Front Frame
Option MTU and MTP, MultiTouch User Interface Upgrade Kits Removal of Option EXM, External Mixing Parts from Original Front Frame This procedure applies only to instruments with Option EXM, External Mixing 1. Refer to Figure 19. Disconnect semi-rigid coax cable W27 from the Ext Mixer connector using a 5/16 inch open-end wrench. - Page 34 Option MTU and MTP, MultiTouch User Interface Upgrade Kits 2. Refer to Figure 20. Use a deep 5/16-inch socket wrench to loosen and remove the ¼" hex nut (2950-0223) and ¼" lock washer (2190-0067) on the inside of the front frame that is attaching the Ext Mixer connector to the front frame.
-
Page 35: Prepare New Front Frame Assembly
Option MTU and MTP, MultiTouch User Interface Upgrade Kits Prepare New Front Frame Assembly 1. Locate the new Front Frame Assembly (N9020-60261) in the kit. 2. Choose the proper Keypad Overlay depending upon the frequency range option of the EXA signal analyzer: a. -
Page 36: Add Ext Mixer Connector And Cable To Front Frame Assembly
Option MTU and MTP, MultiTouch User Interface Upgrade Kits Add EXT MIXER Connector and Cable to Front Frame Assembly This procedure applies only to analyzers with Option EXM, External Mixer. Proceed to the next section if Option EXM is not installed. 1. - Page 37 Option MTU and MTP, MultiTouch User Interface Upgrade Kits 4. Connect one end of W27 to the SMA female connector as shown in Figure 5. Orient W27 so that the cable slopes upward from the Ext Mixer connector at a 15 degree angle.
-
Page 38: New Front Frame Installation
Option MTU and MTP, MultiTouch User Interface Upgrade Kits New Front Frame Installation 1. Refer to Figure 24. Reattach the ribbon cable W1. Ensure the locking tabs are engaged. 2. Carefully install the front panel assembly making sure that the ribbon cables are not pinched. Figure 24 Front Panel Cable Installation Note N9010-90072... - Page 39 Option MTU and MTP, MultiTouch User Interface Upgrade Kits 3. Refer to Figure 25. Carefully position the Front Frame Assembly onto the chassis. Ensure no cables are crushed. Secure with the eight screws (0515-2032) (1) included in the kit, four on each side of the chassis.
- Page 40 Option MTU and MTP, MultiTouch User Interface Upgrade Kits 4. If Option EXM, External Mixing, is not installed, skip steps 5 through 7. 5. Refer to Figure 26. When the front panel is installed, cables W27 and W28 typically do not align.
- Page 41 Option MTU and MTP, MultiTouch User Interface Upgrade Kits 7. Refer to Figure 28. Use a ¼” open-end wrench to prevent the SMA female connector on W28 from twisting. Use a 5/16” torque wrench to torque the nut on W27 to 10 inch-pounds. Figure 28 Torque Cable W28 onto W27 8.
-
Page 42: Final Installation
Option MTU and MTP, MultiTouch User Interface Upgrade Kits Final Installation Final Installation for Standard Instruments (Benchtop Configuration, Figure 14 1. Refer to Figure 14. Carefully slide the instrument cover back onto the instrument from the rear of the analyzer, making sure not to damage any internal cables. The seam on the cover should be on the bottom of the instrument. -
Page 43: Verify Hardware Installation
A full calibration is required to assure the instrument meets all specifications For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your local Keysight office access the following URL, or if in the United States, call the following telephone number: http://www.keysight.com/find/assist... - Page 44 This information is subject to change without notice. © Keysight Technologies 2016 Edition 1, June 2016 N9010-90072 www.keysight.com...