Related Manuals for Vaisala K-PATENTS PR-43-IA Series
Summary of Contents for Vaisala K-PATENTS PR-43-IA Series
- Page 1 IM-EN-PR43IAAX-A Instruction Manual Vaisala K-PATENTS® Process Refractometer PR-43-...-IA/AX/CU...
- Page 2 Vanha Nurmijärventie 21, FI-01670 Vantaa, Finland P.O. Box 26, FI-00421 Helsinki, Finland +358 9 8949 1 Visit our Internet pages at www.vaisala.com. General safety considerations The process medium may be hot or otherwise hazardous. Use shields and protective clothing adequate for the process medium - do not rely on avoid- ance of contact with the process medium.
- Page 3 Note. Notes contain additional information and hints. ® This product manual is delivered to the end user with a Vaisala K-PATENTS product. Information in this manual is subject to change without notice. When the manual is changed, a revised copy is published at http://www.kpatents.com/ Warranty For standard warranty terms and conditions, see www.vaisala.com/warranty.
- Page 4 Document/Revision No. Effective: October 1, 2019 IM-EN-PR43IAAX...
-
Page 5: Table Of Contents
EU declaration of conformity for PR-43-...-IA (ATEX) ... . 25 EU declaration of conformity for PR-43-...-AX (ATEX) ... . 27 © Copyright Vaisala 2019. All rights reserved. - Page 6 PR-43-...-IA/AX/CU instruction manual Document/Revision No. Effective: October 1, 2019 IM-EN-PR43IAAX...
-
Page 7: Introduction
Zone 1: An area in which an explosive gas-air mixture is likely to occur in normal operation. The Vaisala K-PATENTS® Intrinsically Safe Process Refractometer PR-43-...-IA can be in- stalled in hazardous locations in Zone 0 and Zone 1 areas. The PR-43-...-IA refractome-... - Page 8 “n” Note: Servicing of the PR-43-...-IA and PR-43-...-AX/CU refractometers is only allowed for trained service personnel of Vaisala and its representatives. Servicing must be done according to separate instructions defined by Vaisala and must be reported to Vaisala. Document/Revision No.
-
Page 9: Equipment
PR-8436-... and an isolator PR-10930. The ATEX/IECEx certified refractometers and isolators are identified by the nameplate, see Figures 2.1 and 2.2. 3-A and EHEDG Non-sanitary refractometer certified refractometer Figure 2.1 Refractometer PR-43-...-IA nameplates Figure 2.2 Isolator nameplate © Copyright Vaisala 2019. All rights reserved. -
Page 10: Atmosphere
PR-43-...-IA/AX/CU instruction manual 2.2 PR-43-...-AX/CU refractometers for potentially explosive atmosphere The Vaisala K-PATENTS® refractometer system for potentially explosive atmosphere locations consists of a modified refractometer PR-43 and a connecting cable. The ATEX/IECEx and CSA certified refractometers are identified by the refractometer name- plate, see Figure 2.3 and Figure 2.4 below. -
Page 11: Mounting
Choose the mounting location of the refractometer and the isolator so that they are protected from sudden impact and friction. If any of the system parts is affected by a sudden impact, power it off immediately and have it checked by trained Vaisala service personnel before it is used again. - Page 12 PR-43-...-IA/AX/CU instruction manual 9,02 6,56 7,87 2,98 1,57 Figure 3.1 Isolator dimensions (drawing 3785) Document/Revision No. Effective: October 1, 2019 IM-EN-PR43IAAX...
- Page 13 3 Mounting Figure 3.2 Mounting PR-43-...-IA with isolator and PR-8435 cable for Ethernet, mA output and power © Copyright Vaisala 2019. All rights reserved.
- Page 14 PR-43-...-IA/AX/CU instruction manual Figure 3.3 Wiring PR-43-...-IA with isolator and PR-8435 cable for Ethernet, mA output and power Document/Revision No. Effective: October 1, 2019 IM-EN-PR43IAAX...
- Page 15 3 Mounting Figure 3.4 Mounting PR-43-...-IA with isolator and PR-8432 cable for mA output and power © Copyright Vaisala 2019. All rights reserved.
- Page 16 PR-43-...-IA/AX/CU instruction manual Figure 3.5 Wiring PR-43-...-IA with isolator and PR-8432 cable for mA output and power Document/Revision No. Effective: October 1, 2019 IM-EN-PR43IAAX...
- Page 17 3 Mounting Figure 3.6 Mounting PR-43-...-IA with isolator, PR-8432 cable for mA and power, and a separate Ethernet cable © Copyright Vaisala 2019. All rights reserved.
- Page 18 PR-43-...-IA/AX/CU instruction manual Figure 3.7 Wiring PR-43-...-IA with isolator, PR-8432 cable for mA and power, and a separate Ethernet cable Document/Revision No. Effective: October 1, 2019 IM-EN-PR43IAAX...
- Page 19 3 Mounting Figure 3.8 Refractometer cabling © Copyright Vaisala 2019. All rights reserved.
- Page 20 PR-43-...-IA/AX/CU instruction manual Figure 3.9 Refractometer cabling when using Compact user interface CI Document/Revision No. Effective: October 1, 2019 IM-EN-PR43IAAX...
- Page 21 3 Mounting Figure 3.10 Refractometer cabling when using Multichannel user interface MI © Copyright Vaisala 2019. All rights reserved.
-
Page 22: Mounting Pr-43
PR-43-...-IA/AX/CU instruction manual 3.2 Mounting PR-43-...-AX system The refractometer can be installed in a hazardous area up to Zone 2. Use either platform cable PR-8430 or split cable PR-8431 as needed to connect the refractometer e.g. to a DCS. Zone 2 Unclassified area PR-43 sensor Ethernet (M12 connector) - Page 23 3 Mounting Figure 3.12 Connection options for a stand-alone refractometer © Copyright Vaisala 2019. All rights reserved.
- Page 24 PR-43-...-IA/AX/CU instruction manual Figure 3.13 Installing a PR-43-...-AX system with a CI Document/Revision No. Effective: October 1, 2019 IM-EN-PR43IAAX...
- Page 25 3 Mounting Figure 3.14 Installing a PR-43-...-AX system with a MI © Copyright Vaisala 2019. All rights reserved.
-
Page 26: Connector Cover For Pr-43
PR-43-...-IA/AX/CU instruction manual Important: Tampering and replacement with other than Vaisala K-PATENTS® origi- nal components is not allowed because this may affect adversely the safe use of the system. Warning! Refractometer connector shall not be connected or disconnected when the circuits are energized. - Page 27 Qty. Spare part nr. 1 PR-43-AC/AP/PC refractometer Ex Connector cover with screws PR-14104 2 M3x25 DIN 7985 TX 3 M12 Ex connector cover 4 M12 8 pin (F) connector Figure 3.15 Mounting the connector cover © Copyright Vaisala 2019. All rights reserved.
- Page 28 PR-43-...-IA/AX/CU instruction manual Unclassified area Class I Div. 2/Zone 2 Figure 3.16 Cabling in a conduit tube Document/Revision No. Effective: October 1, 2019 IM-EN-PR43IAAX...
- Page 29 AVERTISSEMENT! - RISQUE D’EXPLOSION. NE PAS DÉBRANCHER SI LE CIRCUIT EST TOUS TENSION, À MOINS QUE LE MILIEU SOIT LIBRE DE SUBSTANCES INFLAMMABLES CONCENTRÉES. - Substitution of components may impair suitability for WARNING! - EXPLOSION HAZARD Class I, Division 2. © Copyright Vaisala 2019. All rights reserved.
- Page 30 PR-43-...-IA/AX/CU instruction manual - La substitution de composants peut rendre ce AVERTISSEMENT! - RISQUE D’EXPLOSION matériel inacceptable pour les emplacements de Classe I, Division 2. Document/Revision No. Effective: October 1, 2019 IM-EN-PR43IAAX...
-
Page 31: Regulatory Compliance
– EMC requirements – intended for use in industrial locations Notified body Eurofins Expert Services Oy (number 0537) has issued EU-type examination certificate EESF 19 ATEX 056X for this product. Signed for and on behalf of Vaisala Oyj, in Vantaa, on 1 September 2019 ______________________________________ Jari-Pekka Mörsky... - Page 32 PR-43-...-IA/AX/CU instruction manual Document/Revision No. Effective: October 1, 2019 IM-EN-PR43IAAX...
-
Page 33: Eu Declaration Of Conformity For Pr-43
– EMC requirements – intended for use in industrial locations Notified body Eurofins Expert Services Oy (number 0537) has issued EU-type examination certificate EESF 19 ATEX 058X for this product. Signed for and on behalf of Vaisala Oyj, in Vantaa, on 1 September 2019 ______________________________________ Jari-Pekka Mörsky... - Page 34 PR-43-...-IA/AX/CU instruction manual Document/Revision No. Effective: October 1, 2019 IM-EN-PR43IAAX...
- Page 36 www. v aisala.com...