Tektronix 7B70 Time Base Instruction Manual page 103
Hide thumbs
Also See for 7B70 Time Base:
- Instruction manual (126 pages) ,
- Instruction manual (105 pages) ,
- Instruction manual (117 pages)
Table of Contents
Advertisement
CALIBRATION TEST EQUIPMENT REPLACEMENT
Calibration Test Equipment Chart
This chart compares TM 500 product performance to that of older Tektronix equipment. Only those
characteristics where significant specification differences occur, are listed. In some cases the new instrument
may not be a total functional replacement. Additional support instrumentation may be needed or a change in
calibration procedure may be necessary.
Comparlson of Main Characteristics
DM
501
re~laces7D13
1
PG
501
replaces
107
PG
502
replaces
107
108
11 1
I
PG
501 -
Risetime less than
3.5
nsec into
50
n.
PG
501
-
5
V output pulse;
3.5
nsec Risetime.
PG
501
-
Risetime less than
3.5
nsec;
8
nsec
Pretrigger pulse delay.
PG
501
-
+5
V output.
PG
501
-
Does not have Paired, Burst, Gated,
Delayed 8 Undelayed pulse mode;
+5
V dc Offset; short proof out-
put. Has
5 5
V output.
PG
502
-
5
V output
PG
502 -
Risetime less than
1
nsec;
10
nsec
Pretrigger pulse delay.
PG
502
-
+5
V output.
PG
502
-
Does not have Paired, Burst; Gated,
Delayed 8 Undelayed pulse mode;
+5
V output. Short proof output.
PG
502
-
Does not have Paired, Delayed. Un-
delayed and output locked mode;
f
5
V output.
107
-
Risetime less than
3.0
nsec into
50
n.
108
-
10
V output pulse;
1
nsec Risetime.
111 -
Risetime
0.5
nsec;
30
to
250
nsec
Pretrigger Pulse delay.
114
-
f l O
V output. Short proof output.
115
-
Paired, Burst, Gated, Delayed 8 Un-
delayed pulse mode; f
10
V output.
Short proof output.
108
-
10
V output.
111
-
Risetime
0.5
nsec;
30
to
250
nsec
Pretrigger pulse delay.
114
-
f 1 0
V output. Short proof output.
115 -
Paired, Burst, Gated, Delayed 8 Un-
delayed pulse mode;
f l O
V output.
Short proof output.
2101
-
Paired, Delayed, Undelayed and out-
put locked on mode;
10
V output.
PG
506
replaces
106
067-0502-01
PG
506
-
Positive-going trigger output signal
at least
1
V; High Amplitude,
60
V
output.
PG
506
-
Does not have chopped feature.
106
-
Positive and Negative-going trigger
output signal,
50
nsec and
1
V; High
Amplitude output,
100
V.
0502-01
-
Comparator output can be alter-
nately chopped to a reference
voltage.
SG
503
replaces
190,
190A, 190B
191
067-0532-01
TG
501
replaces
180,
180A
SG
503 -
Amplitude range
5
mV to
5.5
V p-p.
SG
503
-
Frequency range
250
kHz to
250
MHz.
SG
503
-
Frequency range
250
kHz to
250
MHz.
TG
501
-
Marker outputs,
5
sec to
1
ns.
Sinewave available only at
5,2,
and
1
ns. Trigger output
-
slaved
to marker output from
5
sec
through
100
ns. Only one time-mark
190B
-
Amplitude range
40
mV to
10
V p-p.
191 -
Frequency range
350
kHz to
100
MHz.
0532-01
-
Frequency range
65
MHz to
500
MHz.
can be generated.
TG
501
-
Marker outputs,
5
sec to
1
ns. Sine-
wave available only at
5, 2,
and
1
ns.
TG
501
-
Marker outputs.
5
sec to
1
ns. Sine-
wave available only at
5, 2,
and
1
ns. Trigger output
-
slaved to
marker output from
5
sec through
100
ns. Only one time-mark can be
generated.
180A
-
Marker outputs,
5
sec to
1
ps.
Sinewave available at
5, 10,
and
50
MHz. Trigger pulses
1, 10.
100
Hz;
1,10,
and
100
kHz.
Multiple time-marks can be stacked.
181
-
Marker outputs,
1, 10, 100, 1000,
and
10,000,
plus
10
MHz sinewave.
!901
-
Marker outputs,
5
sec to
0.1
ps.
Sinewave available at
5. 10,
and
50
ns. Separate trigger pulses, from
5
sec to
0.1
ps. Multiple time-marks
can be stacked.
- ---
---
-
Scans by ArtekMedia O 2006
Advertisement
Chapters
Table of Contents
Troubleshooting
Need help?
Do you have a question about the 7B70 Time Base and is the answer not in the manual?