WAREMA WMS Wall-mounted transmitter plus Operating And Installation Instructions page 3

Iperating elements on the back
Fig. 4 Operating elements on the back
Pos. Fig. Function
Batteries

The WMS Wall-mounted transmitter plus requires a
coin cell CR 2032 battery.
Learn button

Activates or closes the learn mode of the
WMS Wall-mounted transmitter plus
 L LCED
Indicates that the WMS Wall-mounted transmitter
plus is in learn mode (lights up green)
Iperation
Iperating the products
Cction/result
Button/
WMS Hand-held transmitter/Wall-mounted trans-
display
mitter plus
+
Select the channel using the
Operate the selected product using the
UP/STOP/DOWN buttons.
The operating instructions of the respective
receiver describe which operating options are
available to you (e.g. UP=ON, DOWN=OFF,
STOP=switch).
The transmission LED

transmission is occurring:
Flashes GRCECEO:
WMS Wall-mounted transmitter plus is
transmitting, then:
Lights up GRCECEO for 2 s:
The receiver has confirmed the command.
Lights up RCED for 2 s:
The command has not been confirmed
(e.g. the receiver is outside of the trans-
mission range), or the WMS Hand-held
transmitter plus/Wall-mounted transmitter
plus was added to the network but a chan-
nel has not yet been copied into the
WMS Wall-mounted transmitter plus.
Lights up GRCECEO for 2 s + control
function_LCED red:
The receiver confirms the command, but
does not execute it because of the displayed
control function (e.g. the awning is not ex-
tended because the wind alarm is active).
The transmission LED

transmission is occurring:
Lights up RCED for 2 s:
The WMS Wall-mounted transmitter plus
was added to the network but a receiver
has not yet been assigned.
2018151_d•en•2019-10-01
Learning/recalling the comfort positions
A comfort position can be saved for the receivers in the
network (e.g. awning half extended). The awning can be
automatically moved to this comfort position at the press
of a button.
Button/
display
Uo learn in the comfort position:
Uo recall a comfort position:
+
button.
O IUTCCE
O IUTCCE
indicates that
O IUTCCE
Switching the comfort control functions on/off
Button/
display
+
indicates that
Cction/result
WMS Hand-held transmitter/Wall-mounted trans-
mitter plus
Move your product to the position that is
to be saved as the comfort position (see
"Operating the products").
Hold down the comfort button
seconds until the transmission LED
lights up.
The transmission LED

mission is occurring:
2 s GRCECEO:
The comfort position is saved.
2 s RCED:
The command was not confirmed (e.g.
receiver outside of transmission range);
repeat the procedure.
+ Select the channel using the
Briefly press the comfort button
The transmission LED

The comfort position for the selected prod-

uct is restored automatically.
If a product is already in the comfort position
or if a comfort position has not been saved,
the selected product does not respond to brief
pressing of the comfort button
When the comfort position is not moved to
correctly, the run time in the receiver must be
adjusted with a WMS Central transmitter or a
WMS Hand-held transmitter (please see the op-
erating instructions of the respective receiver).
When the [DOWN] function button is pressed
again while the sun shading product is being
lowered, it always moves to 100% (lower limit
position) and the "Position DOWN" value is
ignored.
Cction/result
WMS Hand-held transmitter/Wall-mounted trans-
mitter plus
+
Select the channel using the
Briefly press the buttons
+
taneously.
The transmission LED

The transmission LED

GRCECEO: The control functions are
switched on in all receivers.
Not all receivers could be
RCED:
reached; switch the control
functions OFF and ON again
(or ON and OFF).
We reserve the right to make technical changes
for 5
indicates that trans-
+
button.
.
flashes green.
:
+
button.
+ and simul-
flashes green.
lights up:
3