Related Manuals for BDI SEQUEL 20
Summary of Contents for BDI SEQUEL 20
- Page 1 SEQUEL 20 6151/6152 ® LIFT DESK INSTRUCTION MANUAL LET’S GET STARTED. 6151 SHOWN DESIGN MATTHEW WEATHERLY...
- Page 3 Please save it for future reference. Your Sequel 20 Lift Desk is designed for indoor use on level floors. It has been engineered for easy assembly. Please follow these directions carefully to prevent any damage.
- Page 4 HARDWARE AND COMPONENTS Unpack and identify the parts listed below. The assembly workspace should be a non-marring surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at customerservice@bdiusa.com. Do not use power tools for assembly of this product.
- Page 5 HARDWARE AND COMPONENTS PART # PART # PART # DESCRIPTION Keypad DESCRIPTION Control Module DESCRIPTION QUANTITY QUANTITY QUANTITY PART # PART # PART # DESCRIPTION Cord Extension DESCRIPTION Foot DESCRIPTION Power Cord QUANTITY QUANTITY QUANTITY PART # PART # DESCRIPTION DESCRIPTION Wire Tray Cord Conduit...
- Page 6 Attach 2 (H3) Cord Wraps (Kleet) using (H2) Short Wood Screws. NOT INCLUDED Phillips Screwdriver Left hand Right hand Choose side side Route cord through hole in metal frame Groove for keypad cord 6 | BDIUSA.COM SEQUEL 20 6151 & 6152...
- Page 7 STEP 2. CONNECT & SECURE KEYPAD ASSEMBLY Attach keypad cord into the (C2) Control PART/DESCRIPTION Module socket (labeled HS) and bundle the slack with the hook and loop tie. Secure the keypad cord into the groove using 6 (H7) Cord H2-WOOD SCREW Clips and 6 (H2) Short Wood Screw.
- Page 8 Connect 1 leg cord to the end of (C4) Cord Extension, connect the other leg cord to the other end of the (C2) Control Module and bundle H5-SCREW up any slack using the hook and loop ties. 8 | BDIUSA.COM SEQUEL 20 6151 & 6152...
- Page 9 STEP 4. INSTALL FEET ASSEMBLY Attach (C5) Feet with (H4) Flathead Screws PART/DESCRIPTION and (T1) Hex Wrench. Make sure the longer end of the feet are facing the front of the desk (same side as keypad). T1-HEX WRENCH H4-SCREW Long end this side NEED ASSISTANCE? customerservice@bdiusa.com BDIUSA.COM | 9...
- Page 10 (C7) Wire Tray to make the H5-SCREW monitor arm attach more centrally. Attach the metal (C7) Wire Tray to the back edge of the bottom of the desk with 2 (H5) Screws. Shifted Right Shifted Left 10 | BDIUSA.COM SEQUEL 20 6151 & 6152...
- Page 11 STEP 6. ATTACH SURGE PROTECTOR—NOT INCLUDED ASSEMBLY Secure 4 pairs of (H9) Dual-Lock Dots to the PART/DESCRIPTION bottom corners of your surge protector. H9-DUAL LOCK DOT Surge Protector (not included) Attach Dual Lock together ATTACH YOUR SURGE PROTECTOR—NOT INCLUDED Determine where you prefer your surge protector to be mounted. We suggest just behind the metal rails towards the leg closest to your wall outlet.
- Page 12 Attach the (6159) Optional Drawer (for 6151/6152) using 4 Screws that came with your drawer as shown. 6159 ASSEMBLY STEP 8. PLUG POWER CORD Plug the (C6) Power Cord into the power port on the (C2) Control Module (labeled AC). 12 | BDIUSA.COM SEQUEL 20 6151 & 6152...
- Page 13 2 PERSON TASK STEP 9. ATTACH DUAL LOCK FASTENER—OPTIONAL ASSEMBLY With the help of another person, carefully pick up, rotate, and place the desk on to its feet. Plug the other end of the Power Cord into the nearest wall socket. Refer to the User Manual on Page 18 and follow the Reset Procedure.
- Page 14 5 holes. Secure the H6-SCREW (C8) Glass Panel in place from below using 5 (H6) Screws. Do not over tighten. Open drawer to attach front, center screw. Place (C9) Grommet Cover into the grommet hole. 14 | BDIUSA.COM SEQUEL 20 6151 & 6152...
- Page 15 STEP 12. ATTACH CORD CONDUIT—OPTIONAL ASSEMBLY Remove adhesive film and attach the (C6) Cord Conduit to the back of the top section of the leg nearest the wall outlet. Insert power cord(s) into (C6) Cord Conduit. NEED ASSISTANCE? customerservice@bdiusa.com BDIUSA.COM | 15...
- Page 16 1" away from the grommet hole. The Sequel Lift Desk can support 75lb (34Kg) on a monitor arm. Optional Monitor Arm (not included) 16 | BDIUSA.COM SEQUEL 20 6151 & 6152...
-
Page 17: Fine Tuning
FINE TUNING WIPE EXCESS LEG LUBRICANT When new, the legs may have excess lubricant. Extend the legs to their highest position and wipe off excess lubricant with a clean, dry cloth or rag. NEED ASSISTANCE? customerservice@bdiusa.com BDIUSA.COM | 17... -
Page 18: Reset Procedure
5. Press and hold the DOWN button again until the desk lowers a little bit more, slightly rises and stops. 6. Release the DOWN button. Your desk is now ready for use. “Reset” Down Memory looks like this 18 | BDIUSA.COM SEQUEL 20 6151 & 6152... -
Page 19: Height Adjustment
The desk base can be adjusted by pressing and holding either the UP or DOWN button until the desired height is reached. To program up to four presets, use the up/down buttons to find a desired height, then press “BDI” followed by a number 1-4. To Change the Movement Program (explained below) follow the Reset Procedure to Step 4. -
Page 20: Setting The Upper And Lower Limits
“BDI” button and the LED display should read “S”. Next, press and release the UP button. Now, press and hold the “BDI” button (for about 2 seconds) until the LED display changes to 999 and then automatically returns to show the selected height. The new upper limit is now set. - Page 21 M1 and M2. You’re Perform a system Done! reset. Is the same leg still lagging or is the same error code number shown? Contact BDI Contact BDI Contact Customer Service Customer Service to replace the to replace the leg Customer...
-
Page 22: Care And Maintenance
While BDI’s stained wood finishes are stable in tone & appearance, all finishes are subject to some degree of discoloration with prolonged exposure to direct sunlight. Please take care to avoid positioning your BDI cabinet in any area with extensive direct sunlight. -
Page 23: Warranty
WARRANTY BDI warrants to the original purchaser that for the below stated warranty term, BDI will repair or replace any product, part, or component covered by this warranty which fails under normal use as a result of a defect in material or workmanship. BDI will repair or replace the aforementioned product, part or component with a comparable product, part or component. - Page 24 These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. Sequel & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2020, BDI | V.05.28.2020 Made in Vietnam.