SpectraLink IP-DECT Server 200 Interoperability Manual
Ringcentral office
Hide thumbs
Also See for IP-DECT Server 200:
- Installation and configuration manual (456 pages) ,
- Configuration manual (49 pages) ,
- Interoperability manual (31 pages)
Related Manuals for SpectraLink IP-DECT Server 200
Summary of Contents for SpectraLink IP-DECT Server 200
- Page 1 Spectralink IP-DECT Server 200/400/6500 Interoperability Guide RingCentral Office 14232912-IG, Edition 1.0 May 2020, Original document...
- Page 2 The drawings and specifications contained herein are the property of Spectralink and shall be neither reproduced in whole or in part without the prior written approval of Spectralink, nor be implied to grant any license to make, use, or sell equipment manufactured in accordance herewith.
-
Page 3: Table Of Contents
Spectralink IP-DECT Server Configuring the Spectralink IP-DECT Server Basic Network Settings SIP Settings Enabling Feature Codes Adding Users and Handsets To Add Users to the Spectralink IP-DECT Server from the Web Based Admin- istration Page 14232912-IG, Edition 1.0 May 2020, Original document... -
Page 4: About This Guide
About This Guide This guide describes how to configure a Spectralink IP-DECT Server 200/400/6500 for con- necting to RingCentral Office. In the following the servers will be referred to as “Spectralink IP-DECT Server”. This guide is intended for qualified technicians and the reader is assumed to have a basic know- ledge about the Spectralink IP-DECT Server and RingCentral Office. -
Page 5: Related Documentation
Available online at http://support.spectralink.com/products. Spectralink DECT Training material In order to gain access to the Spectralink training mater- ial, you must attend training and become Spectralink Cer- tified Specialist. Please visit http://- partneraccess.spectralink.com/training/classroom-train-... -
Page 6: Feature List
Spectralink IP-DECT Server 200/400/6500 Interoperability Guide Feature List The following features are supported: Supported features Telephony Make and receive basic calls, local and PSTN Handset-to-handset calling Check Voicemail Speed Dial Caller ID Call Hold and Retrieve Call Transfer (warm, blind) -
Page 7: Configuration And Feature Details
Spectralink IP-DECT Server 200/400/6500 Interoperability Guide Configuration and Feature Details Supported features Description/Setting Make and receive basic Allows user to make and answer calls. calls, local and PSTN Handset-to-handset calling Allows user to make handset-to-handset calls. Check Voicemail Check for voice messages (*86). - Page 8 Spectralink IP-DECT Server 200/400/6500 Interoperability Guide Supported features Description/Setting DTMF Supports touch-tone feature codes. Secure Voice - TLS 1.2 Encrypted call security. 14232912-IG, Edition 1.0 May 2020, Original document...
-
Page 9: Ringcentral Office
Spectralink IP-DECT Server 200/400/6500 Interoperability Guide RingCentral Office Each individual DECT handset must be assigned to a RingCentral user extension. Spectralink DECT Handsets are configured in RingCentral as a user's existing device. Assign an Existing Device to an Existing Extension To add an existing device to an existing user, do the following: 1. - Page 10 Spectralink IP-DECT Server 200/400/6500 Interoperability Guide 3. Select either Domestic or International. 4. Select Other Phones, click Existing Phone, and then click Add. You can now see information about added devices and order summary. 14232912-IG, Edition 1.0 May 2020, Original document...
- Page 11 Spectralink IP-DECT Server 200/400/6500 Interoperability Guide 5. Assign a phone number to the device: If you already have an existing number, click Existing Number to add it to the device. If you want to add a new number to the device, click New Number, and then select the desired number.
- Page 12 Spectralink IP-DECT Server 200/400/6500 Interoperability Guide 7. Follow the steps to complete the process. Click Done when finished. When complete, the new Existing Device is displayed under the selected user account. Continue setting up new user phones if needed. 14232912-IG, Edition 1.0...
-
Page 13: Get The Ringcentral Sip Settings To Provision Spectralink Dect Handset
Get the RingCentral SIP Settings to Provision Spec- tralink DECT Handset Before configuring the Spectralink IP-DECT Server, get the RingCentral SIP settings for each hand- set. The SIP settings are configured on the Spectralink IP-DECT Server allowing handsets to register with RingCentral Office. Once the handset is registered, its able to make and receive calls. - Page 14 A Setup & Provisioning page appears. 4. On the Setup & Provisioning page, select Other Phones, and then click Select to select the Existing Phone to get the provisioning details which will be used to setup the Spectralink device. 14232912-IG, Edition 1.0...
- Page 15 Authorization ID into a text notepad. This information is used to configure the user in the Spectralink IP-DECT Server. 6. Click Done. 7. Repeat steps 1-6 for each user who will use a Spectralink DECT Handset. 14232912-IG, Edition 1.0 May 2020, Original document...
-
Page 16: Spectralink Ip-Dect Server
Spectralink IP-DECT Server 200/400/6500 Interoperability Guide Spectralink IP-DECT Server Below is a description of how to configure the Spectralink IP-DECT Server and how to add users and handsets to the system. Note: It is assumed that you have installed and configured the Spectralink IP-DECT Server solution including deployment and administration of base stations before continuing the configuration described below. -
Page 17: Configuring The Spectralink Ip-Dect Server
DHCP server making it extremely easy to configure all media resources and base stations. If the Spectralink IP-DECT Server is configured using DHCP, it is necessary to assign a reservation for the device on the DHCP server. -
Page 18: Sip Settings
Spectralink IP-DECT Server 200/400/6500 Interoperability Guide SIP Settings The Spectralink IP-DECT Server requires a few SIP settings to be adjusted in order to connect prop- erly to the RingCentral Office. Note: SIP settings not mentioned below should be left at their default values. - Page 19 Spectralink IP-DECT Server 200/400/6500 Interoperability Guide To modify the SIP settings from the web based Administration Page: 1. Get the IP address for the RingCentral Outbound Proxy URL by using a PING command via PC terminal (Mac) or Command (Windows).
- Page 20 Spectralink IP-DECT Server 200/400/6500 Interoperability Guide Example of SIP configuration: 4. Click Save, and then reboot the system. 14232912-IG, Edition 1.0 May 2020, Original document...
-
Page 21: Enabling Feature Codes
Spectralink IP-DECT Server 200/400/6500 Interoperability Guide Enabling Feature Codes The advanced feature, Call forward unconditional, is accessed by dialing special feature codes from the DECT handsets. To provide access to the Call forward unconditional feature, the fea- ture codes must be enabled. -
Page 22: Adding Users And Handsets
Adding Users and Handsets Each individual DECT handset/user must be added to the Spectralink IP-DECT Server and also on to the RingCentral Office. This section describes how to add the handsets to the Spectralink IP- DECT Server. To Add Users to the Spectralink IP-DECT Server from the Web Based Admin- istration Page 1. - Page 23 Spectralink IP-DECT Server 200/400/6500 Interoperability Guide Field Setting Disabled (Optional) If enabled, the user is disabled. Ensure that this is not enabled. Note: A disabled user cannot make calls from the handset. Username/Extension Enter the RingCentral Username provided with the SIP Settings for the extension.
- Page 24 Please refer to the relevant handset documentation for this. Note: You can subscribe up to 12 handsets for Spectralink IP-DECT Server 200, up to 60 hand- sets for Spectralink IP-DECT Server 400, or up to 4000 handsets for Spectralink IP- DECT Server 6500 to register to RingCentral Office;...
Need help?
Do you have a question about the IP-DECT Server 200 and is the answer not in the manual?
Questions and answers