tams elektronik LD-G-9 Manual

Locomotive decoder for dc engines dcc format

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

für Gleichstrommotoren

Locomotive Decoder

Décodeur pour locomotive

avec moteur continu

voor gelijkstroommotoren

Art.-Nr. 22-01-073

Art.-Nr. 22-01-074

LD-G-9

Lokdecoder

DCC-Format

for DC engines

DCC format

Format DCC

Locdecoder

DCC-format

Anleitung

Manual

Mode d´emploi

Handleiding

Table of Contents

Summary of Contents for tams elektronik LD-G-9

Page 1 LD-G-9 Lokdecoder für Gleichstrommotoren DCC-Format Locomotive Decoder for DC engines DCC format Décodeur pour locomotive Anleitung avec moteur continu Manual Format DCC Locdecoder Mode d´emploi voor gelijkstroommotoren Handleiding DCC-format Art.-Nr. 22-01-073 Art.-Nr. 22-01-074...
Page 2 © 08/2005 Tams Elektronik GmbH Alle Rechte, insbesondere das Recht der Vervielfältigung und Verbreitung sowie der Übersetzung vorbehalten. Vervielfältigungen und Reproduktionen jeglicher Form bedürfen schriftlichen Genehmigung durch die Tams Elektronik GmbH. Deutsch Technische Änderungen vorbehalten. © 08/2005 Tams Elektronik GmbH English All rights reserved.
Page 3: Table Of Contents
LD-G-9 English Table of contents How to use this manual Intended use Safety instructions EMC declaration Information: Speed mode Information: Configuration variables (CVs) Operation overview Technical specifications Checking the package contents Required tools and materials Safe and correct soldering Mounting the locomotive decoder...
Page 4: How To Use This Manual
English LD-G-9 How to use this manual If you have no specialist technical training, this manual gives step-by- step instructions for safe and correct fitting of the module, and operation. Before you start, we advise you to read the whole manual, particularly the chapter on safety instructions and the FAQ chapter.
Page 5: Safety Instructions
LD-G-9 English Safety instructions Mechanical hazards Cut wires can have sharp ends and can cause serious injuries. Watch out for sharp edges when you pick up the PCB. Visibly damaged parts can cause unpredictable danger. Do not use damaged parts: recycle and replace them with new ones.
Page 6 English LD-G-9 Fire risk Touching flammable material with a hot soldering iron can cause fire, which can result in injury or death through burns or suffocation. Connect your soldering iron or soldering station only when actually needed. Always keep the soldering iron away from inflammable materials.
Page 7: Emc Declaration
LD-G-9 English EMC declaration This product is developed in accordance with the European standards EN 55014 and EN 50082-1, tested corresponding to the EC - directive 89/336/EWG (EMVG of 09/11/1992, electromagnetic tolerance) and meets legal requirements. To guarantee the electromagnetic tolerance you must take the following precautions: §...
Page 8: Operation Overview
LD-G-9 Operation overview The decoder LD-G-9 is designed for operation in DCC format and can be adjusted to one of 127 basic addresses or to one of 10.239 extended addresses. It is designed to be controlled from digital control units that are set on the 14-, 28- or the 128-speed mode.
Page 9 LD-G-9 English § Alternative velocity characteristic for mode 28 speed levels (CV#67 to 94) * § Assignment of the outputs X9 to X11 to the function keys F0 to F4 (CV#112 to 114) * § Assignment of the outputs X9 to X11 to the function keys F5 to F8 (CV#115 to 117) * §...
Page 10 English LD-G-9 Shunting gear In the speed modes 14 and 28, it is possible to switch into the shunting gear mode via a function key, when so programmed. In the shunting gear mode, the velocity of all speed levels is reduced to approx. 50 % compared to the set velocity.
Page 11: Technical Specifications
LD-G-9 English § Switching on and off depending on the direction of travel. § Flashing with a frequency of 2 Hz with two phases which are out- of-phase by 180 degrees. Example of use: individual flash lights or alternating flash lights.
Page 12: Required Tools And Materials
English LD-G-9 Required tools and materials Make sure you have the following tools, equipment and materials ready for use: § an electronic soldering iron (max. 30 Watt) with a fine tip, § a soldering iron stand, § a tip-cleaning sponge, §...
Page 13: Mounting The Locomotive Decoder
LD-G-9 English solder (not too much). As soon as the solder becomes liquid take it away. Hold the soldering tip at the spot for a few seconds so that the solder flows into the joint, then remove the soldering iron.
Page 14 English LD-G-9 Connecting the lighting and other accessories to the function outputs X4 to X10 Disconnect any existing diodes in the leads to the lamps. Follow the connection diagrams fig. 1 and fig. 2. Connect the lamps and other accessories to the function outputs (X4 to X10) on the front of the decoder.
Page 15 LD-G-9 English Accessory to be switched via F1: X6 Accessory to be switched via F2: X7 Accessory to be switched via F4: X8 Accessory to be switched via F5: X9 Accessory to be switched via F6: X10 Accessory to be switched via F7: X11 (max. 20 mA!) Tip: Before starting to program the locomotive decoder you should connect the motor to the decoder.
Page 16: Programming The Locomotive Decoder
English LD-G-9 Using a NEM 652 interface connector Some locomotives already have an NEM 652 interface connector mounted. Using a convenient connecting plug you save disconnecting the connections and you do not need to solder at the locomotive. The list below shows how to connect the contacts of the interface connector to the connecting points of the locomotive decoder.
Page 17 LD-G-9 English CV-name Remarks Input value / (State of delivery) Basic 1 ... 127 address Starting 0 ... 255 = The voltage to be output to the voltage motor at speed level 1. (10) The value "0" corresponds to 0 Volt, the value "255"...
Page 18 English LD-G-9 CV-name Remarks Input value (State of delivery) PWM-Period 0 ... 23 The value "0" corresponds to 400 Hz, the value "23" to 40 Hz. Extended 1 ... 10239 adress Configuration Numerical value * data 1 Direction "standard" Reverse direction...
Page 19 LD-G-9 English CV-name Remarks Input value / (State of delivery) Configuration 0 ... 127 Numerical value * data 2 Emergency stop at change of direction Emergency stop at F1 Shunting gear mode at F1 Shunting gear mode at F2 Shunting gear mode at F3...
Page 20 English LD-G-9 CV-name Remarks Input value / (State of delivery) Effects 0 ... 255 Numerical value * for the Flickering active outputs: Strobe active MARS light active at backward motion inactive 8 at forward motion inactive 16 Flashing 2 Hz phase A...
Page 21 LD-G-9 English CV-name Remarks Input value / (State of delivery) Assignment 0 ... 15 Numerical value * F5 – F8 to Operation with: the outputs: function key F5 function key F6 function key F7 function key F8 Dimming of 0 ... 8...
Page 22: Improvement Of The Driving Characteristics
English LD-G-9 Improvement of the driving characteristics Locomotives with especially high current consumption or track sections with bad contacts (e.g. some types of points) may give an unsatisfactory performance. improve locomotive performance by soldering a capacitor 100 µF / 35 V between X15 and X16 (see fig.
Page 23: Certification
LD-G-9 English Certification This product conforms with the EC- directive 89/336/EWG on electromagnetic radiation and is therefore CE certified. Conditions of warranty This product is guaranteed for two years. The warranty includes the correction of faults which can be proved to be due to material failure or factory flaw.
Page 24 LD-G-9 LD-G-9 Fig. 1: Anschlussplan - Vorderseite - Connection Diagram - Front - Schéma de connexion - Face avant - Aansluitplan - Frontzijde - Seite - Page - Page - Pagina I Seite - Page - Page - Pagina I...
Page 25 LD-G-9 LD-G-9 Fig. 2: Anschlussplan - Rückseite - Connection Diagram - Rear - Schéma de connexion - Face arrière - Aansluitplan - Achterzijde - Seite - Page - Page - Pagina II Seite - Page - Page - Pagina II...
Page 26 LD-G-9 LD-G-9 Fig. 3: Schaltplan Circuit Diagram Schéma de principe Schakelplan Seite - Page - Page - Pagina III Seite - Page - Page - Pagina III...
Page 27 Actuele informatie en tips: http://www.tams-online.de Garantie und Service: Warranty and service: Garantie et service: Garantie en service: Tams Elektronik GmbH Rupsteinstraße 10 D-30625 Hannover fon: +49 (0)511 / 55 60 60 fax: +49 (0)511 / 55 61 61 e-mail: modellbahn@tams-online.de...

This manual is also suitable for:

22-01-073 22-01-074 n

tams elektronik LD-G-9 Manual

Quick Links

Related Manuals for tams elektronik LD-G-9

Summary of Contents for tams elektronik LD-G-9

This manual is also suitable for:

Table of Contents