Table of Contents
Advertisement
Quick Links
TOYOTA
Preparation
Part Number: PT228-89460
Kit Contents
Item #
Quantity Reqd.
1
1
2
1
3
1
4
1
5
2
6
2
7
1
Hardware Bag Contents
Item #
Quantity Reqd.
1
4
2
4
3
4
4
2
5
2
6
1
Additional Items Required For Installation
Item #
Quantity Reqd.
1
2
Conflicts
Note:
Recommended Tools
Personal & Vehicle
Protection
Safety Glasses
Vehicle Protection
Special Tools
None
Installation Tools
Nylon Panel Removal Tool
Ratchets
Sockets (Deep Well)
Socket Wrench
Extensions
Issue: C
07/06/05
4-RUNNER
Description
High Assembly
Wiring Harness Bracket
Hardware Bag
Hitch Cover
Frame Spacer
Center Spacer
Close-out Panel
Description
M12 x 1.25 x 45 Hex Flange
Bolt (Black)
M12 x 1.25 x 35 Hex Flange
Bolt (Black)
M8 x 1.25 x 25 Bolt w/Trapped
Washer (Black)
M8 x 1.25 x 20 Bolt w/Trapped
Washer (Black)
M6 x 1.00 x 20 hex Flange Bolt
(Black)
Harness Clamp/Cable tie
(P/N 82711-16830)
Description
Notes
Cloth (Shop Towel)
Notes
Notes
e.g. Panel Pry Tool #1
Toyota SST # 00002-06001-01
½" and ⅜"
10 mm, 12 mm, 13 mm,
17 mm
6" min.
2006 -
NOTE: Part number of this accessory may not be
the same as the part number shown.
Torque Wrench (x2)
Exhaust Hanger Removal
Tool
Special Chemicals
None
General Applicability
Note: All V-8 4-Runner vehicles
Recommended Sequence of Application
Item #
Accessory
1
2
3
Vehicle Service Parts
Item #
Quantity Reqd.
1
2
3
Legend
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
Page 1 of 7 pages
TOWING HITCH
0-100 lbf-ft, 0-100 lbf-in
e.g. Snap On P/N YA3202
Notes
*Mandatory
(may be required for reassembly)
Description
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Toyota PT228-89460
Summary of Contents for Toyota PT228-89460
- Page 1 TOYOTA 4-RUNNER 2006 - TOWING HITCH Preparation NOTE: Part number of this accessory may not be Part Number: PT228-89460 the same as the part number shown. Kit Contents Item # Quantity Reqd. Description Torque Wrench (x2) 0-100 lbf-ft, 0-100 lbf-in...
- Page 2 Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). • Please see your Toyota dealer for a copy of this document. 1. Inspection. (a) Inspect parts for damage. 2. Prepare Vehicle for Hitch Installation.
- Page 3 TOYOTA 4-RUNNER 2006 - TOWING HITCH Procedure (e) For vehicles equipped with air suspension, Nylon Panel Removal Tool loosen the air suspension cover by removing the plastic fastener. Save fastener for reinstallation. (Fig. 2-4) Fig. 2-4 (f) Using panel pry tool, unclip harness from the Panel Pry Tool frame.
- Page 4 TOYOTA 4-RUNNER 2006 - TOWING HITCH Procedure 3. Attach Hitch Center to Vehicle. Socket, 17 mm, Extension 6” (a) Install closeout panel and (2) spacer plates to center attachment bracket by hand starting Spacer Plates (2) M12-1.25x45 black bolts through...
- Page 5 TOYOTA 4-RUNNER 2006 - TOWING HITCH Procedure 6. Install Hitch to Frame Rail. (a) Reinstall tie-down bracket to hitch using two (2) M12 x 1.25x35 black bolts in driver side rear most frame locations. (Fig. 6-1, Step 1) (b) Secure hitch to frame using two (2) M12 x 1.25x35 black bolts in passenger side rear...
- Page 6 TOYOTA 4-RUNNER 2006 - TOWING HITCH Procedure 9. Reinstall Vehicle Components. Exhaust Hanger Removal Tool (a) Reconnect exhaust to the exhaust hanger ensuring to fully engage the hanger. (Fig. 9-1) Fig. 9-1 (b) Reinstall the air suspension cover by replacing the one fastener. (Fig. 9-2) (1) If fastener is damaged fit a new fastener, (P/N 90467-09185).
- Page 7 TOYOTA 4-RUNNER 2006 - TOWING HITCH Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Accessory Function Checks Inspection torque (M12 bolts) 60 ± 12 lbf-ft (80 ± 15 N-m) Inspection torque (M8 bolts) 19 ±...
Need help?
Do you have a question about the PT228-89460 and is the answer not in the manual?
Questions and answers