Advertisement
Table of Contents
TOYOTA
Preparation
Part Number: PT427-89060
PT427-8906B
Kit Contents
Item #
Quantity Reqd.
1
1
2
1
Hardware Bag Contents
Item #
Quantity Reqd.
1
4
2
2
3
2
4
4
5
4
6
4
7
6
8
4
9
2
10
2
Additional Items Required For Installation
Item #
Quantity Reqd.
Conflicts
Recommended Tools
Personal & Vehicle
Protection
Vehicle Protection
Special Tools
None
Installation Tools
Screwdriver
Ratchet
Special Chemicals
Cleaner
Issue: A
8/14/06
4RUNNER
Description
Hood protector
Hardware bag
Description
Outside hood bracket
Grill hood bracket
Grill Hook bracket
6-32 well nut
6-32 x 0.5 MS
#6 SS flat washer
10-24 MS
Mylar pad - small
Double-sided tape
Mylar pad – large
Description
Notes
Blanket
Notes
Notes
Phillips, #2
Phillips #2 Bit
Notes
Soap and Water
2006 -
NOTE: Part number of this accessory may not be
the same as the part number shown.
General Applicability
Note-
Recommended Sequence of Application
Item #
Accessory
1
2
3
Vehicle Service Parts
Item #
Quantity Reqd.
1
2
3
Legend
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
Page 1 of 5 pages
HOOD PROTECTOR
*Mandatory
(may be required for reassembly)
Description
Supplier Ref. #I-1136
Advertisement
Table of Contents
Related Manuals for Toyota PT427-89060
Summary of Contents for Toyota PT427-89060
- Page 1 TOYOTA 4RUNNER 2006 - HOOD PROTECTOR Preparation NOTE: Part number of this accessory may not be Part Number: PT427-89060 the same as the part number shown. PT427-8906B Kit Contents General Applicability Item # Quantity Reqd. Description Note- Hood protector Recommended Sequence of Application...
- Page 2 • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Pre-installation Preparation. Inspect and verify the kit contents. Open the hood.
- Page 3 TOYOTA 4RUNNER 2006 - HOOD PROTECTOR Procedure 3. Outer Bracket Installation. Install four (4) well nuts into the outer holes. (Fig. 3-1). Install the outside hood brackets in the locations shown (Fig. 3-2). Fig. 3-1 Attach the bracket to the hood using the 6-32 x ½"...
- Page 4 TOYOTA 4RUNNER 2006 - HOOD PROTECTOR Procedure (c) Attach Grill Hood Brackets to the Grill Hook brackets. Remove paper backing from double-sided tape and adhere to grill, make sure the holes in both brackets (grill and extension) line up. (Fig. 4-3).
- Page 5 TOYOTA 4RUNNER 2006 - HOOD PROTECTOR Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Accessory Function Checks Inspect brackets Six brackets installed on hood. Inspect screws Six screws installed on hood protector Screw tightness Six screws holding hood protector to brackets are firmly tightened.
Need help?
Do you have a question about the PT427-89060 and is the answer not in the manual?
Questions and answers