Advertisement
Quick Links
TOYOTA
HIGHLANDER
Preparation
Part Number: PT427-48080
Kit Contents
Item #
Quantity Reqd.
1
1
2
1
Hardware Bag Contents
Item #
Quantity Req'd. Description
1
8
2
4
3
4
4
4
5
4
6
8
7
8
8
1
Additional Items Required For Installation
Item #
Quantity Reqd.
1
Conflicts
Recommended Tools
Personal & Vehicle
Protection
Vehicle Protection
Special Tools
None
Installation Tools
Screwdriver
Pliers
Special Chemicals
Cleaner
Issue: C
06/18/08
Description
Hood protector
Hardware bag
Hood Bracket
Nylon Fasteners Insert (Round)
Nylon Insert (Square)
Flathead MS Screw
(L=18.5mm)
Nylon Washers
10-24 x 0.5 MS (L=14.5mm)
Mylar
Instruction Sheet
Description
Notes
Blanket
Notes
Notes
Phillips, #2
Notes
Soap and Water
Page 1 of 6 pages
2008 -
NOTE: Part number of this accessory may not be
the same as the part number shown.
General Applicability
Note-
Recommended Sequence of Application
Item #
Accessory
1
Vehicle Service Parts
Item #
Quantity Reqd.
1
2
3
Legend
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous iss
HOOD PROTECTOR
*Mandatory
(may be required for reassembly)
Description
Supplier Ref. #I-1172
Advertisement
Related Manuals for Toyota PT427-48080
Summary of Contents for Toyota PT427-48080
- Page 1 TOYOTA HIGHLANDER 2008 - HOOD PROTECTOR Preparation NOTE: Part number of this accessory may not be Part Number: PT427-48080 the same as the part number shown. Kit Contents General Applicability Item # Quantity Reqd. Description Note- Hood protector Recommended Sequence of Application...
-
Page 2: Pre-Installation Preparation
Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Pre-installation Preparation. (a) Inspect and verify the kit contents. (b) Make sure front edge of hood, where the... - Page 3 TOYOTA HIGHLANDER 2008 - HOOD PROTECTOR Procedure (d) Apply the 1 7/8”(48mm) mylar strips at the edge of the hood in the area of the eight bracket locations. (Fig. 2-3) Note: Mylar tape shall wrap around the edge of the hood and cover 15 mm of the top and the rest on bottom of the hood surface.
- Page 4 TOYOTA HIGHLANDER 2008 - HOOD PROTECTOR Procedure Cover the bracket and SQUARE nylon insert with the rubber weather strip seal. Insert the 18.5mm length screw with the nylan washer and tighten the screw (Fig 2-7 and 2-8) Hood Machine screws...
- Page 5 TOYOTA HIGHLANDER 2008 - HOOD PROTECTOR Procedure An alignment feature has been provided on the shield to aid in centering the part on the hood. Utilize this feature to align with the center hood latch. (Fig 2-12). (f) Attach hood protector to the brackets using the 14.5mm length machine screws.
- Page 6 TOYOTA HIGHLANDER 2008 - HOOD PROTECTOR Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Accessory Function Checks Inspect brackets • Groove in bracket to fit securely along edge of hood. Mylar Installation • Mylar strips should not have air bubbles or wrinkles.
Need help?
Do you have a question about the PT427-48080 and is the answer not in the manual?
Questions and answers