Page 1
User Guide 020-102584-04 Christie IMB-S3...
Page 2
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.
Connecting the Christie NAS device and configuring the network settings....10 Creating a Christie NAS network share folder....... 10 Verifying NFS is enabled and disabling sleep mode.
General safety precautions Read all safety and warning guidelines before installing or operating the product. Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power. Warning! If not avoided, the following could result in death or serious injury.
(NAS) device to play content. The NAS device must be connected to the gigabit Ethernet port labeled NAS on the main projector communication board. Content cannot be stored on the Christie IMB; all content must be stored on a NAS device.
The network attached storage (NAS) device must be configured to use the network file system (NFS) protocol. Christie recommends that you use a static IP address for the NAS device. 1. Verify the NAS device is connected to the gigabit Ethernet port labeled NAS on the main projector communication board.
Complete the procedures in the order they are written. Prerequisites To connect a Christie network attached storage (NAS), install and format the NAS hard drives and verify that they are configured for RAID 5. Connecting the Christie NAS device and configuring the network settings Complete this procedure to connect the Christie NAS device to the network.
Configuring the Christie IMB and NAS communication settings To configure the communication settings between the Christie IMB and the Christie NAS device, you can use the projector touch panel menus. 1. Disconnect the Ethernet cable from the computer and connect it to the NAS port on the main projector communication board (F-Main).
• 3D Line Interleaved: The left eye and right eye data are sent on alternating lines. 3D Sync Input Mode is not required when using the Christie IMB. For GDC IMB devices, the recommended setting is 3D Line Interleaved. ILS File The ILS file associated with the channel.
4. In the Name field, type a name for the certificate file. 5. Tap Accept. Viewing status information You can view the status of the Christie IMB on the master projector. 1. On the master projector touch panel, tap Status. 2. In the Status list, tap Christie IMB.
You upgrade the Christie IMB and the projector software separately. Software upgrades are available on the Christie website. 1. Navigate to the Christie website and download the upgrade package to a USB flash drive. 2. On the side of the touch panel, insert the USB flash drive into the USB port.
A playlist is a list of content files and automated events that play in an order that you define. • To manage minor time gaps between content files, Christie recommends inserting a short period of black screen with no audio. To achieve this, you can insert a BLACK MOS clip into the playlist.
Managing automation Automation controls playback, the projector, and external devices. The Christie IMB includes built-in support for some external automation devices. If the device is not supported, you can use the serial- over-Ethernet protocol to send automation commands. This section provides instructions for managing and defining: •...
Places the projector in full power mode (shutter open, light Wait Delays the execution of a macro Christie ACT actions These are the available built-in commands for the Christie ACT: Command Description Buzzer Activates the buzzer for the specified time (in milliseconds)
You can backup and restore content drive settings, automation definitions, scheduling, and audio and speaker mappings. When you run a backup, a backup file is created on the Christie IMB. You can copy the backup file from the Christie IMB to a USB flash drive.
X'Y'Z' (4:4:4) Compatible cinema formats - 3D video The hardware configuration of the projector in which the Christie IMB is installed can affect frame rate performance. JPEG content must be contained in an Interop or Society of Motion Picture and Television Engineers (SMPTE) Digital Cinema Package (DCP).
This security policy identifies the ports and interfaces available on the device, the roles and services provided, and the critical security parameters protected by the Christie IMB. All users of the Christie IMB must abide by the requirements defined by the Christie IMB security policy. The Christie IMB security policy is available on the National Institute of Standards and Technology (NIST) website (http://csrc.nist.gov/groups/STM/cmvp/documents/140-1/140val-all.htm).
If the Christie IMB is stored outside the projector beyond six months, the battery can fail and you must return the Christie IMB to Christie Digital Systems USA Inc. To allow the Christie IMB to remain out of a projector beyond six months, a charging connector allows the battery to be recharged.
Page 52
Corporate offi ces Worldwide offi ces Christie Digital Systems USA, Inc. Africa United Kingdom Columbia Korea (Seoul) ph: 714 236 8610 ph: +27 (0)11 510 0094 ph: +44 (0) 118 977 8000 ph: +57 (318) 447 3179 ph: +82 2 702 1601 Christie Digital Systems Canada Inc.