Advertisement
Table of Contents
Sistemi elettronici
di Aperture Porte e Cancelli
ARM is an electromechanical not reversible operator with articulated arm and grease lubrication for residential use on big pilasters
and leafs with a max. weight of 180kg and 1,8m length.
24V low voltage power supply for a high safety of use.
Inversion in case of obstacle.
With articulated steel arm with adjustable mechanical stop in opening.
DIMENSIONS (mm)
Fig. 1
STANDARD INSTALLATION
8
1
ARM
FITTING AND CONNECTION INSTRUCTIONS
5
1
2
1 1
3
TECHNICAL DATA
Power Supply
Motor
243
Power
Working temperature
Weight
Max weight of the gate
Max. weight of the leaf
Opening degrees
1 0
7
9
6
4
1 1
2
3
Fig. 2
REV 05 - 10/2007
ARM
230 V (±5%) 50/60 Hz
24V
40 W
-20°C +55°C
12 Kg
180 Kg
1,8 m
110°
1 - Operator 1
2 - Operator 2
3 - Stop in opening
4 - Electronic unit included
5 - Flashing lamp
6 - Rx photocell
7 - Differential switch 16a-0,03a
8 - Tx photocell
9 - Key switch (on request)
10 - Radio receiver + antenna
11 - Column for photocell
12 - Warning plate
ENGLISH
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SEA ARM
Summary of Contents for SEA ARM
- Page 1 FITTING AND CONNECTION INSTRUCTIONS ENGLISH ARM is an electromechanical not reversible operator with articulated arm and grease lubrication for residential use on big pilasters and leafs with a max. weight of 180kg and 1,8m length. 24V low voltage power supply for a high safety of use.
- Page 2 FITTING AND CONNECTION INSTRUCTIONS ENGLISH 1. GATE ARRANGEMENT It is necessary to make controls on the gate to make sure the application of ARM automation can be possible. Make sure that: Fig. 3 A. the gate fixed and moving parts have a strong and crush- proof structure;...
- Page 3 Fig. 5 ASSEMBLING OF THE ARTICULATED ARM - The two articulated arms must be assembled differently, distinguishing the right arm from the left one. See Fig. 7 and 8. Note: Before inserting the pivots lubricate them with water repellent grease Fig.
- Page 4 Aperture Porte e Cancelli FITTING AND CONNECTION INSTRUCTIONS ENGLISH ATTACHMENT OF THE ARTICULATED ARM TO THE MOTOR - Fit the articulated arm into the motor shaft and lock it with the special screws (Fig. 9). Fig. 9 Security box External release Fig.
- Page 5 - Perforate the leaf and attach the front bracket with the screws (Fig. 12) - Before tightening the screws move the front bracket to the right or to the left for a good positioning of the arm on the gate (Fig. 13) Fig.
- Page 6 Sistemi elettronici di Aperture Porte e Cancelli FITTING AND CONNECTION INSTRUCTIONS ENGLISH RELEASE SYSTEM To release operate as follows: Turn the release door and insert the furnished hexagonal T-key into the special hole (Fig. 14) Turn the release key about 180° clockwise (Fig. 15). Extract the key and close the door Open manually the leaf To block again operate as follows:...
- Page 7 - Bring the leaf in complete opening or to the desired opening point. - Put the stop bracket S on the stop with the articulated arm and lock the screw 1 (left-hand side motor Fig. 16, right-hand side Fig. 17).
- Page 8 NOTE: THE MANUFACTURER CAN NOT BE DEEMED RESPONSIBLE FOR ANY DAMAGE OR INJURY CAUSED BY IMPROPER USE OF THIS PRODUCT. SEA reserves the right to do changes or variations that may be necessary to its products with no obligation to notice. Sistemi elettronici di Aperture Porte e Cancelli SEA S.r.l.
Need help?
Do you have a question about the ARM and is the answer not in the manual?
Questions and answers