Special Mode; Special Mode Configuration Buttons - Denon AVR-X5200W Service Manual

SPECIAL MODE

Special Mode Configuration Buttons

No. 1 - 12, 15 :
b
No. 13, 14:
b
No. 16 ：
b
No. Mode
Version Display Mode
1
(u-COM / DSP Error Display)
User Initialization Mode
2
(Settings for the Installer Setup are not
initialized.)
Factory Initialization Mode
3
(Initialization includes settings for the
Installer Setup.)
4
PANEL / REMOTE LOCK Selection Mode
Check the Video/Audio pass
5
Mode
6
Protection History Display Mode
7
232C Standby Clear Mode
8
Operation Info Mode
TUNER STEP Mode
9
(E3 and E2 model only)
10
Remote ID Setup Mode
11
Installer Setup Mode
12
Protection Pass Mode
13
CX870 / CY920 Reboot Mode
14
CX870 / CY920 Initialization Mode
15
USB Update Mode
16
Forced USB All Device Write Mode
NOTE :
When the volume indicator displays "
cannot be used.
To cancel this special mode, press and hold the "CURSOR f "and "STATUS" buttons for 3 seconds and longer. When the volume indica-
tor returns to the normal display, RS-232C communication can be used.
Hold down buttons "A", "B" and "C" at the same time and press the power button to turn on the power.
Hold down buttons "A" and "B" for at least 3 seconds while the power is on.
Press the "A" and "B" buttons simultaneously while inserting the AC plug to turn the power on.
Button A Button B Button C
SETUP OPTION
BACK INFO
CURSOR CURSOR
d
STATUS INFO
ZONE3
STATUS
SOURCE
↑
↑
↑
↑
↑
CURSOR
BACK
0
CURSOR
STATUS
0
DIMMER SETUP
CURSOR
DIMMER
1
STATUS OPTION
STATUS OPTION
", the set has entered a special mode for developers. In this case, RS-232C communication
ZONE3 BACK
SOURCE
STATUS
X
Displays the version of firmware such as the main firmware or DSP,
- etc. Errors that have occurred are displayed.
(See 19 page)
Initializes backup data.
-
(Settings for the Installer Setup are not initialized.)
Initializes backup data.
-
(Initialization includes settings for the Installer Setup.)
f
Start this unit in the PANEL/REMOTE LOCK selection mode so that
- PANEL LOCK and Remote Lock can be selected as ON or OFF.
(See 23 page)
This is a special mode for service confirmation used during repair
work to simplify the confirmation work for the Audio channel/video
-
channel.
(See 27 page)
Displays the protection occurrence history.
↑ -
(See 70 page)
Switches from 232C standby mode to normal standby mode.
↑ -
(See 71 page)
Displays the total operating time of the set, number of times
the power was switched on, and number of occurrences of each
↑ -
protection.
(See 72 page)
Enables reception STEP of the ANALOG TUNER to be changed.
↑ -
(See 73 page)
If there are multiple DENON AV receivers in the same area, this mode
stops the other AV receivers from being operated concurrently with
↑ -
this device.
(See 74 page)
Access the Remote Maintenance mode via the internet.Installer Setup
- is displayed on Setup menu / Network.
b Refer to AVR_RemoteMaintenance_.pdf of SDI.
Enables the power to be turned on when protection detection is in
ZONE3
the stopped state.
SOURCE
(See 75 page)
- Restarts CX870 / CY920. (See
Enter this mode only after replacing Flash for CX870 / CY920 and
-
rewriting the firmware. (See
Switches this unit to USB Update mode.
-
(See 79 page)
Mode used when this unit cannot be recovered.
-
Forcibly switches this unit to USB update mode.
(See 81 page)
INFO OPTION
d
SETUP
f
DIMMER
0 1
18
Contents
75 page)
76 page)