Special Mode; Special Mode Setting Button - Denon AVR-X3200W Service Manual

SPECIAL MODE

Special mode setting button

No. 1 - 6, 9 : While holding down buttons "A", "B" and "C" simultaneously, press the power button to turn on the power.
b
No. 7, 8 : While the power is on, hold down buttons "A" and "B" for at least 3 seconds.
b
No. 10 : While holding down buttons "A" and "B" simultaneously, insert the AC plug into the wall outlet to turn on the power.
b
No. Mode
Version Display
1
(u-COM / DSP Error Display)
2
Selecting the Mode for Service-related
2-1
Protection history display mode
2-2
Check the Video/Audio path Mode
2-3
Remote ID Setup Mode
TUNER STEP Mode
2-4
(E3 and E2 model only)
2-5
Operation Info Mode
3
User Initialization Mode
4
Factory Initialization Mode
5
PANEL / REMOTE LOCK Selection Mode
6
Protection Pass Mode
7
CY920 Reboot Mode
8
CY920 Initialization Mode
9
USB Update Mode
10
Forced USB All Device Write Mode
SOURCE SELECT
X
Button A Button B Button C
DIMMER STATUS
ZONE2
DIMMER
SOURCE
TUNER
PRESET CH -
+
↑ -
↑ -
↑ -
↑ -
TUNER TUNER
PRESET CH PRESET CH
- +
ZONE2
DIMMER
SOURCE
TUNER
ZONE2
PRESET CH
SOURCE
+
TUNER
ZONE2
PRESET CH
SOURCE
-
TUNER TUNER
PRESET CH PRESET CH
- +
ZONE2
DIMMER
SOURCE
TUNER
STATUS
PRESET CH
s
-
TUNER
PRESET CH STATUS
-
TUNER ZONE2
PRESET CH ON/OFF
PHONES
TUNER
ZONE2
TUNER PRESET CH +
SOURCE
PRESET CH -
Displays the version of firmware such as the main firmware or DSP.
- Errors that have occurred are displayed.
(See page 19 )
This is a display for turning on each service-related mode.
STATUS
Service-related modes: No. 2-1 - No. 2-5
Displays the protection occurrence history.
-
(See page 57)
This is a special mode for service confirmation used during repair
work to simplify the confirmation work for the Audio channel /
-
video channel.
(See page 28)
If there are multiple DENON AV receivers in the same area, this
mode prevents other AV receivers from being operated concur-
-
rently with this device.
(See page 61)
Enables reception STEP of the ANALOG TUNER to be changed.
-
(See page 60)
Displays the accumulated operating time of the unit, the number
- of times the power was switched on, and the number of occur-
rences of each protection. (See
Initializes backup data.
-
(Settings for the Installer Setup are not initialized.)
Initializes backup data.
-
(The settings for the Installer Setup is also initialized.)
Start this unit in the PANEL/REMOTE LOCK selection mode so that
- PANEL LOCK and Remote Lock can be switched between ON and
OFF. (See page
Enables the power to be turned on when protection detection is
STATUS
disabled. (See page
- The CY920 is restarted after CY920 hang up.
Enter this mode only after replacing Flash for CX870 / CY920 and
-
rewriting the firmware.
- Switches this unit to USB Update mode.
Mode used when this unit cannot be recovered.
- Forcibly switches this unit to USB update mode.
(See page 70)
ZONE2
1 2 3 MEDIA
DIMMER STATUS CBL/SAT Blu-ray
PLAYER
SOURCE
QUICK SELECT
AUX 1 - HDMI SETUP MIC
DIMMER
18
Descriptions
page 59)
23)
62)
MASTER VOLUME
4
ONLINE
STATUS