Quantum Scalar i40 Replacement Manual
  1. Manuals
  2. Brands
  3. Quantum Manuals
  4. Storage
  5. Scalar i40
  6. Replacement manual

Quantum Scalar i40 Replacement Manual

System control board replacement
Hide thumbs Also See for Scalar i40:
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

Taking ESD Precautions

© 2014 Quantum Corporation. All rights reserved. Quantum, the Quantum logo, DLT, DLTtape, the DLTtape logo, SuperLoader,
Scalar, DXi, StorageCare, StorNext, GoProtect, and Vision are registered trademarks of Quantum Corporation and its affiliates
in the United States and/or other countries. All other trademarks are the property of their respective owners. Quantum
specifications are subject to change.
6-66556-04 Rev B, February 2014
Scalar i40 and Scalar i80:
These instructions explain how to remove a System Control Board (SCB) from
®
your Scalar
i40 or Scalar i80 library, and replace it with a new one.
The SCB contains library firmware, tape drive firmware, all configurable settings,
license keys, and SKM TLS certificates. After you replace the SCB, you must
either restore a previously saved configuration, or reinstall the license keys and
manually reconfigure the settings.
Note: When you replace the SCB you will permanently lose all data previously
collected for logs and reports.
To replace the SCB, refer to the following sections:
•
Taking ESD Precautions
•
•
•
•
To avoid damaging static-sensitive parts while performing this procedure,
observe the following precautions:
• Use an antistatic wrist strap. If you do not have one, touch the outside of
the library on the sheet metal before touching any components, to
discharge static from your body.
System Control Board
on page 1
on page 2
on page 4
on page 4
on page 5
Replacement
*6-66556-04*

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Scalar i40 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Quantum Scalar i40

Summary of Contents for Quantum Scalar i40

  • Page 1 © 2014 Quantum Corporation. All rights reserved. Quantum, the Quantum logo, DLT, DLTtape, the DLTtape logo, SuperLoader, Scalar, DXi, StorageCare, StorNext, GoProtect, and Vision are registered trademarks of Quantum Corporation and its affiliates in the United States and/or other countries. All other trademarks are the property of their respective owners. Quantum specifications are subject to change.
  • Page 2 Quantum Scalar i40 and Scalar i80: System Control Board Replacement 6-66556-04 Rev B February 2014 • Keep static-sensitive parts in their original shipping containers until ready for installation. Look for the ESD sticker to identify static-sensitive parts. • Avoid touching connectors and board components.
  • Page 3 6 Disconnect the power cords from the power supplies on the back of the library. The Scalar i40 has one power supply. The Scalar i80 may have one or two power supplies. Make sure you disconnect all power cords from the power supplies.
  • Page 4 Quantum Scalar i40 and Scalar i80: System Control Board Replacement 6-66556-04 Rev B February 2014 Replacing the System Control Board These instructions explain how to replace the defective SCB. 1 Position the new SCB for installation as follows: a Place the board components face up. (The flat part of the board faces down.)
  • Page 5 Quantum Scalar i40 and Scalar i80: System Control Board Replacement 6-66556-04 Rev B February 2014 buttons to view the screens. You can only change these settings via the Web client. • No — You are asked if you want to use DHCP.
  • Page 6 The IVT takes about 30 minutes. If any problems are detected, the library issues a diagnostic ticket. 9 Package the old SCB in the packaging that shipped with the new SCB, and send the old SCB back to Quantum using the return shipping label included in the package. Configuring the Library...
  • Page 7 6 If you are connecting to a Scalar Key Manager (SKM), take note that TLS certificates will need to be loaded onto the library. For instructions, refer to Scalar i40 and i80 User Guide, Checking and Installing TLS Certificates on the Library 7 Save the library configuration.
  • Page 8 Quantum Scalar i40 and Scalar i80: System Control Board Replacement 6-66556-04 Rev B February 2014 9 Package the old SCB in the packaging that shipped with the new SCB, and send the old SCB back to Quantum using the return shipping label included in the package. Configuring the Library...

This manual is also suitable for:

Scalar i80

Table of Contents