Advertisement
Step 5
LAN (Ethernet) port
Use CAT5 cross-cable standards such as the bottom. The device's
default IP address is 192.168.0.100. Users can use the RS232 or
USB interface to modify the IP address. CAT5 cross-line, refers to
the end of the T568A standard on one end for the T568B standard.
Ethernet control interface module for non-standard modules
PIN
PIN
T568A
1
1
2
2
3
3
White-orange
4
4
5
5
Insert Twisted
6
6
Pair Wires
7
7
White-brown
RJ-45
8
8
Connector
Step 6-USB connector
3 USB interface for computer software AVDSP
Console.exe control. USB interface, 11 and 16 for the
LED control system, control, use the USB cable
Step 7-Serial port
Pin
2
3
5
7
Insert Twisted
Pair Wires
8
RS232/RS422
Connector
Pin
1
2
3
4
Step 8-power connector
Plug in power cord which has IEC connector, VSP 310
support AC power from 85 to 260 VAC,50-60Hz,
which means world wide compatible.
Powering up
Push power button switcher to ON position. LCD
module on the front panel will show RGBLINK and
VSP 310 model information, and go into self
verification before it load the last setting configuration
data and send the processed image to the target display
or device. For the first time running, CV1 input is the
default input source. User can operate with VSP 310
with local front panel and remote control with the
software run on the PC, remote control by RS232, USB
or TCP/IP.
Address:S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: 00865925771197
Email: rgblinkcs@gmail.com
End 1
End 2
Wire color
Wire color
绿白
White-green
White-orange
green
Orange
桔白
White-green
Green
蓝色
蓝色
Blue
Blue
T568B
蓝白
蓝白
White-blue
White-blue
桔白
桔白
绿色
Orange
Green
桔色
棕白
棕白
White-brown
棕色
绿白
棕色
Brown
Brown
T568A
T568B
RS-232
Function
RS-422
TX
Transmit
TX-
RX
Receive
RX-
GND
Signal Ground
GND
---
Not used
RX+
---
Not used
TX+
RJ-11
Function
---
Not used
RX
Receive
TX
Transmit
Insert Twisted
GND
Signal Ground
Fax:00865925771202
http://www.rgblink.com
Local control -- Front Panel Operation
Step 1
Push OUT button and use UP or DOWN button to go to
CAT5
the right resolution for the monitor or display system,
T568A
and push SEL button to decide to go to the resolution.
standard one
NOTE
end, other
800x600x60Hz,1024×768×60Hz , 1280×768×60Hz
end to
1280×1024×60Hz ,1440×900×60Hz, 1400×1050×60Hz
T568B
1920×1080×60Hz 1600×1200×60Hz
standard
Output resolution should be the same or
crossover
bigger than monitor or display system resolution.。
cable
Step 2-Input Switch
VSP 310 support DVI and VGA inputs, push DVI or
VGA button, switch to the corresponding input signal
and the signal output by setting the display resolution
and the SCALE value to the terminal device
NOTE
Function
Transmit(-)
Step 3
Receive(-)
Press TP button, enter Test Pattern menu 【Pattern】：
Signal Ground
standard seven color bar
Receive(+)
Step 4
Transmit(+)
Push Scale button and go into scale setting menu. Use UP or
DOWN to go to Horizontal size, Vertical size, Horizontal
position, Vertical position setting page, and push SEL to
decide to set, and use UP or DOWN to change the size or
position value. Push SEL to send and exit from the setting.
Step 5
VSP 310 can handle any input source to fine 2 DVI outputs,
Pair Wires
two DVI outputs which can each support full HD resolution
RJ11
of 1920 * 1080 * 60Hz; and support for the second monitor
Connector
or projector-screen function.
press the MENU button to enter the main menu, press UP /
DOWN button to enter the sub-screen setup menu, press the
SEL button to enter the feature set to confirm, press UP /
DOWN button to set the horizontal or vertical screen split
screen. press the SEL button to view this feature; or directly
click the horizontal split-screen, vertical screen
LED screen applications, the split-screen set of coordinates
set to support full-screen run
Horizontal screen
Step6
First press the AB button to activate the main menu of
seamless transitions, press UP / DOWM button to enter the
main menu screen in different sub-effects, press the SEL
button to confirm the effects of the selected view mode is also
available on the effects menu. effects of the values set; such as
fade switch delay settings. Secondly, the touch input source
button to see a seamless transition effects.
output resolution
VSP 310 support 8output format as following ：
Currently selected input signal when no signal
input, VSP 310 will remain displayed on a
static screen image.
Pattern setting
scale
separate setting
Vertical Screen
Seemless switch
VSP 310 Quick Start
Rev 1.0
Page2 of 3
Advertisement
