Do you have a question about the RoboVac and is the answer not in the manual?
Questions and answers
Paul Johnson
February 25, 2025
RoboVac 115 Front Wheel very stiff on axel. Can I just lever it out without dismantleing machine to free it off ?
1 comments:
Mr. Anderson
February 25, 2025
Yes, you can lever out the front wheel of the EUFY RoboVac 11S without dismantling the machine. You need to insert a tool under the wheel, avoiding the caster, and carefully pry it out. Be cautious not to remove the caster itself, as it may break a plastic clip and cause the wheel to fall out repeatedly.
This answer is automatically generated
Rox
January 25, 2025
I just opened my new ropvacnic. I do not plan to use the fyi mode at this time. How do I disconnect from this mode. Right now the blue button keeps bleaking. Also .. just about 10 minutes ago, it starting beeping continuously until I turned it off. What does a beeping that does not stop mean? The unit is on the recharging mount while beeping
1 comments:
Mr. Anderson
May 14, 2025
The context does not mention a "FYI mode," so how to disconnect it cannot be determined.
Continuous beeping while the RoboVac is on the recharging mount indicates a fault, even if the app shows it is fully charged. This may be due to a battery issue. Replacing the battery may stop the beeping.
Clean the Swivel Wheel Clean the Mopping Cloth and Water Tank Replace the Rubber Strip Troubleshooting Voice Alert Wi-Fi Connection Specifications Customer Service Thank you for purchasing RoboVac. Carefully read all instructions before using this product, and keep this manual for future reference.
Important Safety Instructions remove the main PCB and unscrew the battery cover using a screwdriver. Remove the battery by disconnecting the quick connector. To reduce the risk of injury or damage, read these safety • The used battery should be placed in a sealed plastic bag instructions carefully and keep them at hand when setting and disposed of safely according to local environmental up, using, and maintaining this device.
Page 4
Notice • Do not operate this device in areas with exposed electrical outlets on the floor. This symbol on the device or its packaging • Do not expose the electronics of this device, its battery, indicates: or the integrated Charging Base. There are no user- serviceable parts inside.
Page 5
that interference will not occur in a particular installation. If Maximum output power: 18 dBm this equipment does cause harmful interference to radio or Frequency band: 2.4G band (2.4000GHz - 2.4835GHz) television reception, which can be determined by turning the Contains FCC ID: 2ANDL-WR1 Contains IC: 23243-WR1 equipment off and on, the user is encouraged to try to correct...
Page 6
Consignes importantes de sécurité • La batterie doit être retirée de cet appareil avant de le mettre au rebut. Pour retirer la batterie à partir de cet appareil, retirez d'abord les vis de la partie inférieure, Pour réduire le risque de blessure ou de dommage, lisez puis retirez le circuit principal et dévissez le couvercle de attentivement les consignes de sécurité...
Page 7
d'un cordon d'alimentation et le traîne avec lui, un objet peuvent présenter un comportement imprévisible peut tomber d'une table ou d'une étagère. risquant d'entraîner un incendie, une explosion ou une blessure. • Si la pièce à nettoyer possède un balcon, une barrière physique doit être utilisée pour empêcher l'accès au • N'exposez pas la batterie ou l'appareil au feu ou à...
Page 8
Déclaration FCC L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Cet appareil est conforme au Chapitre 15 du règlement Sciences et Développement économique Canada FCC. Le fonctionnement est soumis aux deux conditions applicables aux appareils radio exempts de licence. suivantes : (1) l'appareil ne doit pas produire de brouillage, L'exploitation est autorisée aux deux conditions suivantes : et (2) l'utilisateur de l'appareil doit accepter tout brouillage...
About Your RoboVac Avis de marque déposée • Amazon, Echo, Alexa et tous les logos associés sont des marques commerciales d'Amazon.com, Inc. ou de ses What's in the Box filiales. • Apple et le logo Apple sont des marques déposées d'Apple Inc., enregistrées aux États-Unis et dans d'autres pays.
RoboVac Anatomy C. Dust Collector A. Top & Side Filter Auto cleaning control button Wi-Fi status light Bumper D. Suction Inlet Infrared sensor Dust collector Dust collector Dust collector release button B. Bottom Drop sensor Charging contact pins Charging contact pins...
Flashing red + Voice alert Refer to the “Troubleshooting>Voice Alert” section in Keep RoboVac away from wet areas. this manual for solutions. RoboVac may climb on top of objects less than 0.63 in/16 mm in height. Remove these objects if possible.
Remove objects within 3 ft/1 m of the left and right side and within 6 ft/2 m of the front of the Charging Base. If you cannot remove the objects, check whether RoboVac can return to the Charging Base normally; if not, contact eufy customer service for help.
• RoboVac has a pre-installed rechargeable battery that has to be fully charged before EufyHome use. • RoboVac returns to the Charging Base at the end of a cleaning cycle or when its battery is running low. 1. Download the EufyHome app from the App Store (iOS devices) or Google Play (Android devices).
• If you have any problems during the Wi-Fi setup process, refer to the “Troubleshooting > Wi-Fi connection” section in this Manual. • If RoboVac gets stuck in any space, tap Find My Robot in the app to find the machine.
Spot cleaning You can select the Spot cleaning mode in the EufyHome app. In Spot mode, RoboVac intensively cleans a specific area for 2 minutes in a spiral pattern. Useful if there is a concentrated area of dust or debris.
Page 16
Remove the water tank and put the dust collector back into the main unit. Install the water tank into the bottom of RoboVac until a click is heard. • After mopping, remove the water tank, empty any remaining water and...
Before you start, make sure that: Dust Collector After each use • RoboVac is attached to the Charging Base to ensure there is enough power. Filter Once every week Every 2 months (Twice a week if you have a pet) • RoboVac is connected with the EufyHome app.
Open and empty the dust collector. Place the filter back into the dust collector. Push the dust collector back into the main unit. Remove the filter. Clean the Side Brushes Tap the filter to remove dust. Foreign substances, such as hair, can easily get tangled in the side brushes, and dirt may adhere to them.
Clean the Sensors and Charging Pins Carefully unwind and pull off any hair or string that is wrapped between the main unit and the side brushes. Use a cloth dampened with warm water to remove dust from the brushes or to To maintain the best performance, clean the drop sensors and charging pins regularly.
Clean any hair or debris wrapped around the wheel or entangled inside the wheel Remove the cover plate and then take out the rubber strip. cavity. Reinstall the wheel and push in until it clicks into place. Do not clean the swivel wheel with water. Clean the Mopping Cloth and Water Tank It is recommended to clean the mopping cloth and water tank after each use.
• Check if there are any Internet connection problems. • Check if you can hear a beep when RoboVac is docked onto the Charging Base. If not, contact the eufy service • Check whether you have installed the Amazon Alexa center to repair or replace the Charging Base.
- If the issue persists, contact customer support for help When an error or issue occurs, the red indicator on RoboVac will flash and you will hear a specific voice prompt. Follow the voice prompt to solve the problem. - Check whether the fan blades are stuck in an...
2.4GHz frequency band. RoboVac does not support 5GHz frequency band. Light - If RoboVac cannot connect to the Wi-Fi network and you are using a 2.4/5GHz • RoboVac is turned off. mixed network, switch to a 2.4GHz network for Wi-Fi setup. You can switch back • Charge RoboVac by attaching it to the...
Need help?
Do you have a question about the RoboVac and is the answer not in the manual?
Questions and answers
RoboVac 115 Front Wheel very stiff on axel. Can I just lever it out without dismantleing machine to free it off ?
Yes, you can lever out the front wheel of the EUFY RoboVac 11S without dismantling the machine. You need to insert a tool under the wheel, avoiding the caster, and carefully pry it out. Be cautious not to remove the caster itself, as it may break a plastic clip and cause the wheel to fall out repeatedly.
This answer is automatically generated
I just opened my new ropvacnic. I do not plan to use the fyi mode at this time. How do I disconnect from this mode. Right now the blue button keeps bleaking. Also .. just about 10 minutes ago, it starting beeping continuously until I turned it off. What does a beeping that does not stop mean? The unit is on the recharging mount while beeping
The context does not mention a "FYI mode," so how to disconnect it cannot be determined.
Continuous beeping while the RoboVac is on the recharging mount indicates a fault, even if the app shows it is fully charged. This may be due to a battery issue. Replacing the battery may stop the beeping.
This answer is automatically generated
Battery down
How do i reprogram my X10 Pro Omni