Cable Entry (Kle); Blanking Plug; Closing The Device; Taking Into Operation; Maintenance/Servicing - Eaton Crouse-Hinds Series Operating Instructions Manual

Fig. 9
Item 1 Item 3
Item 2
Code for voltage and No. of poles
acc. to IEC
Voltage Colour
2-pole + PE
110 - 130V 50/60Hz yellow
200 - 250V 50/60Hz blue
3-pole + PE
200 - 250V 50/60Hz blue
480 - 500V 50/60Hz black
380 - 415V 50/60Hz red
600 - 690V 50/60Hz black
3-pole + N + PE
480 - 500V 50/60Hz black
380 - 415V 50/60Hz red
600 - 690V 50/60Hz black
10
Plug and socket system 32 A, GHG 522
6.3 Cable entries (KLE);
blanking plugs
6.3.1 Plug and socket
Item 4
Flexible cables shall be used with
trumpet-shaped cable glands or other
suitable entries with additional pull-relief.
When using cable entries with a lower IP
protection than that which applies to the device
(see page 7 , technical data), the IP protection of
the whole device will be reduced.
The mounting directives applicable to the cable
entries used shall be observed. Unused holes
shall be closed with a blanking plug in order to
establish the minimum protection category.
In case of sealing inserts that are cut out, it
shall be ensured that the insert is properly
adapted to the cable diameter. Care has to be
taken that when fitting the cable entries,
sealing inserts appropriate to the cable
diameter are used. In order to ensure the
required minimum protection category, the
cable glands are to be tightened down.
Overtightening might impair the protection
category.
All vacant metric CEAG cable entries shall be
closed with the certified blanking plug for
metric cable entries.
6.3.2 Plug
Fig. 9: In general, only the sealing inserts fitted
in the plug may be used. When mounting the
cable, attention has to be paid that sealing
inserts matching the cable diameter be used.
After having connected the cable, the coupling
ring item 2 is to be screwed fingertight until the
sealing effect is obtained. Then the screws item
4 of the pull-relief, item 3, are to be tightened
down.
h (PE)
Mind! Overtightening might impair the
4 h
pull-relief effect!
6 h
9 h
6.4

Closing the device

7 h
In order to ensure the required minimum
6 h
protection category, the cover screws, the
5 h
screws of the plug and of the coupler shall be
tightened down. The screws of the plug and the
7 h
coupler shall be tightened down.
6 h
5 h
Overtightening might impair the protection
category.
Any foreign matter shall be removed from
the device.
6.5

Taking into operation

Prior to taking the apparatus into operation, the
tests specified in the relevant national
regulations shall be carried out. Apart from that,
the correct functioning and installation of the
apparatus in accordance with these operating
instructions and other applicable regulations will
have to be checked.
Check the plug for any damages before putting
it in the socket.
The user must ensure that a uniform equipoten-
tial earth applies throughout when the plug and
socket system is operated.
The inappropriate installation and operation
of the plugs and sockets can entail the loss
of warranty.
7

Maintenance/Servicing

Before opening the enclosure, make sure
that the device is disconnected from the
voltage, or take appropriate protective
measures.
The required maintenance intervals depend
on the specific application and will therefore
have to be determined by the user dependent
on the conditions of use.
If during servicing, repairs prove to be
necessary, section 8 of these operating
instructions will have to be observed.
8 Repair / Overhaul /
Modifications
Repairs and overhaul may only be carried out
with genuine CEAG spare parts.
Modifications to the device or changes of its
design are not permitted.
9

Disposal / Recycling

When the apparatus is disposed of, the
respective national regulations on waste
disposal will have to be observed. In order
to facilitate the recycling of individual
components, plastic parts are provided with
the identification mark of the plastic material
used.
Subject to modifications or supplement of the
product range.
GB