Table of Contents
Advertisement
Quick Links
Getting started with X-NUCLEO-OUT10A1 industrial digital output expansion
Introduction
The
X-NUCLEO-OUT10A1
industrial digital output expansion board for
solution for the development of 0.5 A (typ.) digital output modules, letting you easily evaluate the
diagnostic capabilities with industrial loads.
The
X-NUCLEO-OUT10A1
interfaces with the microcontroller on the STM32 Nucleo via 3 kV optocouplers driven by GPIO pins
and Arduino™ UNO R3 (default configuration) and ST morpho (optional, not mounted) connectors.
The expansion board should be connected to either a
stacked with another
X-NUCLEO-OUT10A1
Two
X-NUCLEO-OUT10A1
expansion boards allows you to evaluate a dual channel digital output module with 0.5 A (typ.)
capability each, or a 0.5 A (typ.) single channel safety digital output module. In the second scenario, the first shield output is
connected to the supply of the second one. Dedicated on-board hardware can be enabled or disabled to activate fast discharge
of high capacitive loads, output voltage sensing and additional surge pulse output line protection.
UM2716 - Rev 1 - June 2020
For further information contact your local STMicroelectronics sales office.
NUCLEO-F401RE
or an
X-NUCLEO-OUT08A1
Figure 1.
X-NUCLEO-OUT10A1 expansion board
board for STM32 Nucleo
STM32 Nucleo
provides an affordable and easy-to-use
IPS161HF
or
NUCLEO-G431RB
development board, and can be
.
UM2716
User manual
driving and
www.st.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ST X-NUCLEO-OUT10A1
Summary of Contents for ST X-NUCLEO-OUT10A1
- Page 1 X-NUCLEO-OUT10A1 interfaces with the microcontroller on the STM32 Nucleo via 3 kV optocouplers driven by GPIO pins and Arduino™ UNO R3 (default configuration) and ST morpho (optional, not mounted) connectors. The expansion board should be connected to either a NUCLEO-F401RE...
-
Page 2: Getting Started
UM2716 Getting started Getting started Overview X-NUCLEO-OUT10A1 industrial digital output expansion board, embedding the IPS161HF intelligent power switch (IPS), is designed to meet the application requirement in terms of galvanic isolation between user interface (or logic side) and power interface (or process side). -
Page 3: Power Section
UM2716 Overview Figure 2. X-NUCLEO-OUT10A1 expansion board: digital interface components ® The four Arduino UNO R3 connectors: • allow expansion board communication with the STM32 Nucleo development board accessing STM32 peripheral and GPIO resources; • provide digital supply voltage between the... -
Page 4: Hardware Requirements
UM2716 Hardware requirements Figure 3. X-NUCLEO-OUT10A1 expansion board: power stage components For EMC: • the transient voltage suppressor (U2), enabled by closing J1, is placed between V and GND tracks to protect the IPS161HF against surge discharge on the supply rail path up to ±1 kV/2Ω coupling;... -
Page 5: System Requirements
UM2716 System requirements Figure 4. X-NUCLEO-OUT10A1 and STM32 Nucleo stack System requirements To use the STM32 Nucleo development boards with the X-NUCLEO-OUT10A1 expansion board, you need: • a Windows PC/laptop (Windows 7 or above) • a type A to mini-B USB cable to connect the... - Page 6 UM2716 Board setup Step 8. Push the blue button on STM32 Nucleo board to choose among the examples provided in the default firmware package. Note: When using two boards stacked (e.g. dual channel digital output or single channel safety digital output application), you have to move some signal enabler resistors from DEFAULT to ALTERNATE position.
-
Page 7: Schematic Diagrams
Schematic diagrams Figure 5. X-NUCLEO-OUT10A1 circuit schematic (1 of 2) Analog supply CN10 8V - 60 V 5001 2.2uF SM15T39CA 47uF (N.M.) 4700pF OUT1 EARTH default open Con3 default closed 4700pF STPS1H100A Morpho Connectors (N.M.) OUT1 SSQ-119-04-L-D (N.M.) SSQ-119-04-L-D (N.M.) - Page 8 Figure 6. X-NUCLEO-OUT10A1 circuit schematic (2 of 2) default: default: closed closed 100nF 5001 5001 default closed (open load detection = active) ISO1 Vcc1 Vcc2 ACPL-217-50AE default: closed OUT4 OUT1 DIAG OUT3 OUT1 OUT2 1.5k 5001 OUT1 DIAG default: 3-4 = CLOSE...
-
Page 9: Bill Of Materials
UM2716 Bill of materials Bill of materials Table 2. X-NUCLEO-OUT10A1 bill of materials Item Q.ty Ref. Value Description Manufacturer Order code Ceramic 4700 pF 1825 (4564 Metric) 3000 C1 , C2 capacitors (not Vishay Vitramon HV1825Y472KXHATHV V (3kV) ±10% mounted) 2.2 µF SMD 1206 (3216 Metric) - Page 10 UM2716 Bill of materials Item Q.ty Ref. Value Description Manufacturer Order code Jumpers (not con2-strip-male mounted) con8-2x4-strip-male pitch 2.54 Wurth Electronics J13, J14 Connector headers 61300821121 Inc. StripFET power TO-261-4, TO-261AA 100 V 3.3 W MOSFET in STN2NF10 (Tc) SOT-223 package SMD 27 K Ohm 0603 (1608 R1, R2 Resistors...
- Page 11 UM2716 Bill of materials Item Q.ty Ref. Value Description Manufacturer Order code DO-214AB, SMC 1500 W (1.5 1500 W, TVS in SM15T39CA High-power transient voltage 2-UDFN ESDA15P60-1U1M suppressor (not mounted) UM2716 - Rev 1 page 11/16...
-
Page 12: Revision History
UM2716 Revision history Table 3. Document revision history Date Revision Changes 12-Jun-2020 Initial release. UM2716 - Rev 1 page 12/16... -
Page 13: Table Of Contents
UM2716 Contents Contents Getting started ..............2 Overview . - Page 14 X-NUCLEO-OUT10A1 bill of materials ........
- Page 15 Figure 3. X-NUCLEO-OUT10A1 expansion board: power stage components ....... . 4 Figure 4.
- Page 16 ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’...
Need help?
Do you have a question about the X-NUCLEO-OUT10A1 and is the answer not in the manual?
Questions and answers