Table of Contents
Advertisement
Quick Links
Getting started with the X-NUCLEO-OUT11A1 industrial digital output expansion
Introduction
The
X-NUCLEO-OUT11A1
is an industrial digital output expansion board for
environment for the evaluation of the driving and diagnostic capabilities of the
relay, with embedded galvanic isolation, in a digital output module connected to 0.7 A industrial loads.
The
X-NUCLEO-OUT11A1
directly interfaces with the microcontroller on the STM32 Nucleo driven by GPIO pins and Arduino
R3 connectors.
The galvanic isolation between the microcontroller and the process stage is guaranteed by the ISO808.
The expansion board can be connected to either a
It is also possible to evaluate a system composed of a
UM3079 - Rev 1 - December 2022
For further information contact your local STMicroelectronics sales office.
NUCLEO-F401RE
X-NUCLEO-OUT11A1
Figure 1.
X-NUCLEO-OUT11A1 expansion board
board for STM32 Nucleo
STM32
Nucleo. It provides a powerful and flexible
ISO808
octal high-side smart power solid state
or a
NUCLEO-G431RB
development board.
stacked on other expansion boards.
UM3079
User manual
®
www.st.com
Advertisement
Table of Contents
Related Manuals for ST X-NUCLEO-OUT11A1
Summary of Contents for ST X-NUCLEO-OUT11A1
-
Page 1: Figure 1. X-Nucleo-Out11A1 Expansion Board
UM3079 User manual Getting started with the X-NUCLEO-OUT11A1 industrial digital output expansion board for STM32 Nucleo Introduction X-NUCLEO-OUT11A1 is an industrial digital output expansion board for STM32 Nucleo. It provides a powerful and flexible environment for the evaluation of the driving and diagnostic capabilities of the... -
Page 2: Getting Started
UM3079 Getting started Getting started Overview X-NUCLEO-OUT11A1 embeds the ISO808 intelligent power switch (IPS), which features galvanic isolation, overcurrent and overtemperature protection for safe output loads control. The board is designed to meet the application requirements for the galvanic isolation between the user and power interfaces. -
Page 3: Digital Section
The pin 3 of the connector CN11 can be used to supply the logic side of the ISO808 independently by the expansion board. In this case, on the X-NUCLEO-OUT11A1, the pins 1 and 2 of J4 must be closed (pins 5-6 open). UM3079 - Rev 1... -
Page 4: Power Section
(eight loads can be connected between each pin of CN2, CN3, CN4, and CN12 and pin 2 of CN1), EMC protections (U2), and supply reverse polarity protection (D1). Figure 3. X-NUCLEO-OUT11A1 expansion board: power section components ISO808 Output and power supply connector... -
Page 5: Hardware Requirements
Arduino UNO R3 connector pins on the STM32 Nucleo board as shown below. Figure 4. X-NUCLEO-OUT11A1 and STM32 Nucleo stack System requirements To use the STM32 Nucleo development boards with the X-NUCLEO-OUT11A1 expansion board, you need: •... -
Page 6: Board Setup
UM3079 Board setup Board setup Step 1. Connect the mini-USB or micro-USB cable to your PC to use the X-NUCLEO-OUT11A1 with NUCLEO- F401RE NUCLEO-G431RB development board Step 2. Download the firmware (.bin) onto the STM32 Nucleo development board microcontroller through... -
Page 7: Schematic Diagrams
EXT_Vdd I SO808 direct supply voltage - set to max 3.3V DEFAULT STATUS R108 ESDA7P60-1U1M when X-NUCLEO-OUT11A1 is used with NUCLEO board I OREF Al t er nat e use STATUS R107 100 N.M. N.M. - can be set to max 5.5V... -
Page 8: Figure 6. X-Nucleo-Out11A1 Circuit Schematic (2 Of 2)
Figure 6. X-NUCLEO-OUT11A1 circuit schematic (2 of 2) default: close 1-2, 5-6 10nF con6-2x3-strip-male 10nF default: close 5-6 EXT_Vdd 10nF RED LED 2.2uF SMBJ5.0A-TR con6-2x3-strip-male 0.1uF 10nF LED YELLOW 0.1uF VCC_EP OUT1_1 OUT_EN OUT1_2 OUT1 OUT_EN OUT2_1 SYNCH SYNCH OUT2_2... -
Page 9: Bill Of Materials
UM3079 Bill of materials Bill of materials Table 3. X-NUCLEO-OUT11A1 bill of materials Item Q.ty Ref. Part/value Description Manufacturer Order code 10nF 0603 CAP CER C1 C2 C3 C4 Wurth (1608 Metric) 10000PF 50V 885382206002 C5 C6 C7 C8 Electronics Inc. - Page 10 UM3079 Bill of materials Item Q.ty Ref. Part/value Description Manufacturer Order code BAT48JFILM DIODE SC-76, SCHOTTKY SOD-323 40V 350MA BAT48JFILM 750mV @ SOD323 (not 200mA 350mA mounted) (DC) LED GREEN LED GREEN D3 D4 D5 D6 Wurth 0603 (1608 CLEAR 0603 150060VS75000 D7 D8 D9 D10 Electronics Inc.
- Page 11 UM3079 Bill of materials Item Q.ty Ref. Part/value Description Manufacturer Order code R18 R19 R25 15k 0603 (1608 RES SMD 15K R26 R27 R28 Metric) 0.1W, OHM 1% 1/10W Yageo RC0603FR-0715KL R29 R30 1/10W 1% 0603 R101 R102 R108 R109 100 0603 (1608 RES SMD 100 R110 R111...
-
Page 12: Board Versions
X-NUCLEO-OUT11A1 versions PCB version Schematic diagrams Bill of materials X$NUCLEO-OUT11A1 X$NUCLEO-OUT11A1 schematic diagrams X$NUCLEO-OUT11A1 bill of materials 1. This code identifies the X-NUCLEO-OUT11A1 evaluation board first version. It is printed on the board PCB. UM3079 - Rev 1 page 12/19... -
Page 13: Regulatory Compliance Information
UM3079 Regulatory compliance information Regulatory compliance information Notice for US Federal Communication Commission (FCC) For evaluation only; not FCC approved for resale FCC NOTICE - This kit is designed to allow: (1) Product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a finished product and (2) Software developers to write software applications for use with the end product. -
Page 14: References
UM3079 References References Freely available on www.st.com: • ISO808 datasheet • UM3035: "Getting started with X-CUBE-IPS industrial digital output software for STM32 Nucleo" • NUCLEO-F401RE documentation • NUCLEO-G431RB documentation UM3079 - Rev 1 page 14/19... -
Page 15: Revision History
UM3079 Revision history Table 5. Document revision history Date Revision Changes 02-Dec-2022 Initial release. UM3079 - Rev 1 page 15/19... -
Page 16: Table Of Contents
UM3079 Contents Contents Getting started ..............2 Overview . -
Page 17: List Of Tables
X-NUCLEO-OUT11A1 bill of materials ........ -
Page 18: List Of Figures
X-NUCLEO-OUT11A1 expansion board: digital interface section........3... - Page 19 ST’s terms and conditions of sale in place at the time of order acknowledgment. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of purchasers’...
Need help?
Do you have a question about the X-NUCLEO-OUT11A1 and is the answer not in the manual?
Questions and answers