ST X-NUCLEO-OUT04A1 User Manual
  1. Manuals
  2. Brands
  3. ST Manuals
  4. Computer Hardware
  5. X-NUCLEO-OUT04A1
  6. User manual
ST X-NUCLEO-OUT04A1 User Manual

ST X-NUCLEO-OUT04A1 User Manual

Industrial digital output expansion board for stm32 nucleo
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Getting started with X-NUCLEO-OUT04A1 industrial digital output expansion
Introduction
The
X-NUCLEO-OUT04A1
industrial digital output expansion board for
environment for the evaluation of the driving and diagnostic capabilities of the
state relay) in a digital output module connected to 5.7 A (max.) industrial loads.
The
X-NUCLEO-OUT04A1
interfaces with the microcontroller on the
Arduino UNO R3 (default configuration) and ST morpho (optional, not mounted) connectors.
The expansion board can be connected to either a
It is also possible to evaluate a system composed by up to four stacked
As an example, a system with four
output module with 5.7 A (max.) capability each.
RELATED LINKS
For further details on configuration resistors, refer to UM2863
UM2728 - Rev 1 - August 2021
For further information contact your local STMicroelectronics sales office.
NUCLEO-F401RE
X-NUCLEO-OUT04A1
expansion boards allows you to evaluate an eight-channel digital
Figure 1.
X-NUCLEO-OUT04A1 expansion board
board for STM32 Nucleo
STM32 Nucleo
provides a powerful and flexible
IPS2050H-32
(dual high-side smart power solid
STM32 Nucleo
via 5 kV optocouplers driven by GPIO pins,
or
NUCLEO-G431RB
development board.
X-NUCLEO-OUT04A1
expansion boards.
UM2728
User manual
www.st.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X-NUCLEO-OUT04A1 and is the answer not in the manual?

Questions and answers

Related Manuals for ST X-NUCLEO-OUT04A1

Summary of Contents for ST X-NUCLEO-OUT04A1

  • Page 1: Figure 1. X-Nucleo-Out04A1 Expansion Board

    X-NUCLEO-OUT04A1 interfaces with the microcontroller on the STM32 Nucleo via 5 kV optocouplers driven by GPIO pins, Arduino UNO R3 (default configuration) and ST morpho (optional, not mounted) connectors. The expansion board can be connected to either a NUCLEO-F401RE NUCLEO-G431RB development board.

  • Page 2: Getting Started

    UM2728 Getting started Getting started Overview X-NUCLEO-OUT04A1 embeds the IPS2050H-32 intelligent power switch (IPS), featuring overcurrent and overtemperature protection for safe output load control. The board is designed to meet application requirements in terms of galvanic isolation between user and power interfaces.

  • Page 3: Power Section

    UM2728 Overview Figure 2. X-NUCLEO-OUT04A1 expansion board: digital interface components The four Arduino UNO R3 connectors: • allow expansion board communication with the STM32 Nucleo development board microcontroller accessing STM32 peripheral and GPIO resources; • provide digital supply voltage between the...

  • Page 4: Hardware Requirements

    UM2728 Hardware requirements Figure 3. X-NUCLEO-OUT04A1 expansion board: power stage components Output channel 1 - fault red LED Output channel 2 - fault red LED Output channel 1 - green LED Output channel 2 - green LED IPS2050H-32 Output and power supply connector For EMC: •...

  • Page 5: System Requirements

    UM2728 System requirements Figure 4. X-NUCLEO-OUT04A1 and STM32 Nucleo stack System requirements To use the STM32 Nucleo development boards with the X-NUCLEO-OUT04A1 expansion board, you need: • a Windows PC/laptop (Windows 7 or above) • a type A to mini-B USB cable to connect the...

  • Page 6: Multiple Board Configuration

    Multiple board configuration It is also possible to evaluate an eight channel digital output module by stacking four X-NUCLEO-OUT04A1 with shared or independent supply rail and independent loads. In this case, the four expansion boards (board 0, 1, 2, 3 as shown in the table below) must be properly configured: for board 1, 2 and 3, it is necessary to unsolder four resistors for each board from the default position and solder them back in the alternate positions according to the following table.

  • Page 7: Schematic Diagrams

    Schematic diagrams Figure 5. X-NUCLEO-OUT04A1 circuit schematic (1 of 2) Analog supply CN10 8 V - 60 V OUT1 OUT1 OUT2 4.7nF/3kV(N.M) N.M.(100uF) 2.2uF/100V EARTH CON5 4.7nF/3kV(N.M) OUT2 default open default open CON38 ST morpho connectors (N.M.) CON38 D1STPS1H100A Alternate Nucleo supply...

  • Page 8: Figure 6. X-Nucleo-Out04A1 Circuit Schematic (2 Of 2)

    Figure 6. X-NUCLEO-OUT04A1 circuit schematic (2 of 2) default: closed ISO1 R722k DG1GREEN LED TLP383 default: open default: closed OUT1 OUT1 default: closed FLT1 default: CLOSE 1-2 default: R182.2k CLOSE 1-2 PSSO24 ISO3 TLP383 100nF/100V 100nF/100V default: closed 100nF/100V default:...

  • Page 9: Bill Of Materials

    UM2728 Bill of materials Bill of materials Table 4. X-NUCLEO-OUT04A1 bill of materials Item Q.ty Ref. Part / Value Description Manufacturer Order code Dual high-side IPS2050H-32 smart power IPS2050H-32-TR PSSO24 solid state relay 5 ways, 1 row 24 A TH...
  • Page 10 UM2728 Bill of materials Item Q.ty Ref. Part / Value Description Manufacturer Order code R101, R102, 100Ω 0.1W ±0.5% Resistors Panasonic ERJ3BD1000V R103, R104 0603 R111, R121, R131 R112, R122, R32 Resistors (not R113, R123, mounted) R133 R114, R124, R134 SW1, SW2, 3 ways, 1 row SMD SW3, SW4,...

  • Page 11: Revision History

    UM2728 Revision history Table 5. Document revision history Date Revision Changes 04-Aug-2021 Initial release. UM2728 - Rev 1 page 11/15...

  • Page 12: Table Of Contents

    UM2728 Contents Contents Getting started ..............2 Overview .
  • Page 13 X-NUCLEO-OUT04A1 bill of materials ........
  • Page 14 Figure 3. X-NUCLEO-OUT04A1 expansion board: power stage components ....... . 4 Figure 4.
  • Page 15 ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’...

Table of Contents