Advertisement
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended-use, production operations is available.
Locator
Assembly
(Supplied with
Die Assembly)
Front of Tool
(Locator Side)
Die
Assembly
The PRO-CRIMPER III Hand Crimping Tool is a Commercial" grade tool and
is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 application specification, but may not comply with other
feature parameters of the specification. Tyco Electronics offers a variety of
tools to satisfy your performance requirements. For additional information,
contact the Technical Assistance Center at 1-800-722-1111.
TE
TE
Die Assembly
Locator Assembly
58564-2
58516-1
{
Supplied with die assembly. Also available separately.
1. INTRODUCTION
PRO–CRIMPER III Hand Crimping Tool
Assembly 58564–1 consists of Die Assembly
58564–2 and PRO–CRIMPER III Hand Crimping Tool
Frame 354940–1. The die assembly consists of
crimping dies and a locator assembly.
Read these instructions thoroughly before crimping.
E
2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
PRO-CRIMPER* III Hand
Crimping Tool Assembly 58564-1
with Die Assembly 58564-2
Moving Jaw
Ratchet
Adjustment
Wheel
{
}
TE
TE
Contact
Contact
Family
Universal
Uni ersal
Power
Contacts
Contacts
Figure 1
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
Stationary Jaw
Back of Tool
(Wire Side)
Pivot Pin
PRO-CRIMPER III Hand
Crimping Tool Frame
354940-1 (See 408-9930)
Moving Handle
Insulation Diameter
Size (AWG)
2.01 to 2.69
20 to 18
[.079 to .106]
2.49 to 3.30
16
[.098 to .130]
26 to 22
[.035 to .114]
}
Contact the Tooling Assistance Center or Product Assistance Center. (see below).
Dimensions on this sheet are in millimeters [with
NOTE
inch equivalents provided in brackets]. Figures
i
and illustrations are for identification only and are
not drawn to scale.
Reasons for reissue are provided in Section 11,
REVISION SUMMARY.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
Instruction Sheet
408-4075
05 MAY 09
Stationary
Handle
Wire
Strip Length
(mm [In.])
(mm [In.])
2.69 to 3.71
[.106 to .146]
.89 to 2.90
Rev B
1 of 5
LOC B
Advertisement
Table of Contents
Related Manuals for Tyco Electronics PRO-CRIMPER III 58564-1
Summary of Contents for Tyco Electronics PRO-CRIMPER III 58564-1
- Page 1 114 application specification, but may not comply with other Moving Handle feature parameters of the specification. Tyco Electronics offers a variety of tools to satisfy your performance requirements. For additional information, contact the Technical Assistance Center at 1-800-722-1111.
- Page 2 4. Insert the short die retaining screw through the four die retaining pins, and slide the anvils and jaw and through both anvil dies, and tighten the crimpers out of the tool jaws. of 5 Tyco Electronics Corporation...
-
Page 3: Crimping Procedure
NOT attempt to crimp an improperly positioned the adjustment procedure. contact. Contact Locator Support Back of Tool (Wire Side) Adjustment Contact Screw for Strip (Typ) Contact Length Support Wire Locator Wire in Wire Inserted Stop Slot to Stop Figure 3 of 5 Tyco Electronics Corporation... -
Page 4: Section 7, Crimp Height Adjustment
This inspection requires the use of a micrometer with required, rotate the adjustment wheel a modified anvil. CLOCKWISE to a lower–numbered setting. Tyco Electronics does not manufacture or market NOTE 4. Replace the lockscrew. these gages. However, TE recommends the modified micrometer (Crimp Height Comparator RS-1019-5LP). -
Page 5: Maintenance
Order the repair kit and replaceable parts through your Tyco Electronics representative, or call 1–800–526–5142, or send a facsimile of your purchase order to 1–717–986–7605, or write to: Rev B 5 of 5 Tyco Electronics Corporation...
Need help?
Do you have a question about the PRO-CRIMPER III 58564-1 and is the answer not in the manual?
Questions and answers