Related Manuals for Graco SLIMFIT LX
Summary of Contents for Graco SLIMFIT LX
- Page 1 SLIMFIT LX ™ ALL-IN-ONE CHILD RESTRAINT SYSTEM USER MANUAL 2.5kg 36kg ECE-R44 04 CNS 3972 IMPORTANT - Please read the user manual before use and use this product correctly. NWL0000982161B...
- Page 2 ・...
- Page 3 Read this User Manual completely BEFORE first use of your car seat! Keep this User Manual always with the car seat. Provi- sions are made on the rear of the seat shell. Plan to spend some time getting to know your car seat-time well spent when you consider that your baby’s safety depends on it.
- Page 4 DO NOT ever take a baby out of the car seat for any reason while vehicle is in motion. If your baby needs attention, find a safe place and pull off the road. Do store your car seat in a safe place when not being used.
- Page 5 After an accident, the car seat must be replaced. You may not see any damage, but after a serious crash a car seat can be too weak to protect again. Please contact child restraint manufacturer in the event of any questions. DO NOT use load bearing points other than those specified by restraint manufacturer in the instructions or on the restraint body.
- Page 6 Failure to follow these instructions and child restraint’s labels can result in child striking the vehicle’s interior during a sudden stop or crash. No car seat can guarantee protection from injury in every situation, but proper use helps reduce the risk of serious injury or death.
-
Page 7: Important Warning
. DO NOT use another manufacturers seat cover with this child restraint. See your retailer for Graco replace- ment parts only. DO NOT use in any configuration not shown in the instructions. - Page 9 0-9 kg MUST be rear-facing. Over 18 kg MUST be in booster mode.
- Page 10 •Weight：from 0kg to 13kg •Car seat must be rear-facing in the vehicle seat. •Make sure vehicle seat belt is routed through the rear-facing belt path, marked with a blue label. •Install this car seat tightly in your vehicle. •Harness straps must be or just below the top of child’s shoulders. •Installation using 3-point belt only.
- Page 11 ❶ Push the Recline Handle to recline the Car Seat. ❷ Place the car seat in recline position 1 or 2. ❸ Place the base flat on the vehicle seat. Push it back until the front of the car seat touches the vehicle seat back.
- Page 12 ❹ Unsnap the pad from back (4 locations). ❺ Pull lower seat pad forward to expose the plastic shell. ❻ Thread vehicle lap seat belt through the rear-facing belt path (marked with a blue label) and buckle The seat belt should lay as flat as possible CAUTION and not be twisted.
- Page 13 CAUTION ❼ Thread the shoulder belt through the rear-facing shoulder belt guide on the back of the seat marked with blue labels.The seat belt should lay as flat as possible and not be twisted. In case the seat belt is not long enough when installing the carseat, please lean the carseat CAUTION toward the seat back so the seat belt can route through the seatbelt path on the carseat back completely, once buckled up, please restore the carseat position.
- Page 14 •Weight：from 9kg to 18kg, must be forward- facing in the vehicle seat. •Make sure vehicle seat belt is routed through the forward-facing belt path, marked with a bright red label. •Install this car seat tightly in your vehicle. •Harness straps must be just above the child’s shoulders. •Installation using ISOcatch System and 3-point belt or using 3-point belt only.
- Page 15 Installation using ISOcatch System and 3-point belt ISOcatch •Please do not install using ISOcatch System only. WARNING...
- Page 16 ❶ ISOcatch ISOcatch ISOcatch Fit the ISOcatch guides with the ISOFIX anchor points. The ISOcatch guides can protect the surface of the vehicle seat from being torn. They can also guide the ISOcatch connectors. ❷ Press the ISOcatch adjusting button to pull out the ISOcatch connectors. ❸...
- Page 17 ❹ Line up the ISOcatch connectors with the ISOFIX anchor points, and then click both ISOcatch connectors into the ISOFIX anchor points. • Make sure that both ISOcatch connectors are securely attached to their ISOFIX anchor points. The colors of the indicators on both ISOcatch connectors should be completely green. •...
- Page 18 ❺ Press the secondary lock button first and then the button on the ISOcatch connectors before removing the child restraint from the vehicle seat. ❻ Rotate the ISOcatch connectors by 180 degrees, then press the ISOcatch adjusting button to fold the ISOcatch connectors.
- Page 19 Installation using 3-point belt ❶ Push the Recline Handle to recline the Car Seat. ❷ Place the car seat in recline position 3. ❸ Place the base flat on the vehicle seat. Push it back firmly until the back of the car seat touches the vehicle seat back.
- Page 20 ❹ CAUTION Thread vehicle seat belt through the forward-facing belt path (marked with an bright red label) and buckle it. Make sure buckle and seat belt are in line with each other. The seat belt should lay as flat as possible and not be twisted.
- Page 21 ❻ Press down firmly in the center of the car seat. Pull on the shoulder belt to tighten. ❼ Lift up on the harness release lever while pulling out on the harness straps Ⓐ Unbuckle the buckle . Ⓑ Place harness straps off to the sides.
- Page 22 ❽ Place Harness Straps Over Child’s Shoulders Make sure their back is flat against the car seat back. ❾ You will hear a “click” when buckle tongues are securely attached. Pull up on each buckle tongue to make sure it is securely attached.
- Page 23 2.5 cm Ⓐ Harness straps must be at or just below the child’s shoulders. Ⓑ Top of head must be at least 2.5 cm below the red headrest/harness adjustment handle. Ⓒ Harness straps must be at or just above the child’s shoulders. Ⓓ...
- Page 24 ❶ Squeeze the red adjustment handle and move headrest up or down for the proper harness height. ❷ The correct slot is the one that is closest to your child without being underneath them. ❸ To Adjust, Lift the Lower Seat Pad From Front of Car Seat to Expose The Buckle Slots.
- Page 25 ❻ Pull All the Slack Out From around the Waist, Pull up on the harness strap. Do this to both sides. ❼ Tighten the Harness by Pulling the Harness Adjustment Strap, When you are not able to pinch any of the harness webbing at your child’s shoulder, the harness is tight enough. •When buckling up the seat belt, please watch out for fingerss or hand position to avoid WARNING pinching or getting hurt.
- Page 26 •Weight：from 15kg to 36kg •Car seat must be forward-facing in the vehicle seat. •Remove infant wedge when used as a booster. •Vehicle seat belts MUSTflat against child and MUST NOT be twisted. •Make sure vehicle seat’s shoulder belt is centered between the child’s neck and edge of shoulder. •Installation using ISOcatch System and 3-point belt or using 3-point belt only.
- Page 27 CAUTION •Never use a vehicle lap only seat belt across front of child. •A Vehicle seat belts MUST lay flat against child and MUST NOT be twisted. Make sure vehicle seat’s shoulder belt is centered between the child’s neck and edge of shoulder.
- Page 28 ❶ Loosen the harness straps as much as possible. ❷ Raise the headrest to the highest position. ❸ Unbuckle the buckle. Only need to pull out harness strap, and need to stay away from harness covers.
- Page 29 ❹ Remove the Lower Seat Pad to Expose the Harness Storage Door. It is more convenient to operate after removing the Buckle Cover.
- Page 30 ❺ Twist the crotch belt as shown. Rotate the metal retainer up through the shell. From the front, pull the crotch buckle out. ❻ Open the Harness Storage Door and Place Harness, Buckle, and Buckle Tongues Inside Storage Compartment. Close the Door.
- Page 31 ❼ Place the harness covers in the shell back openings as shown. ❽ Replace Seat Pad, Move the headrest back to its proper position for your child. ❾ Recline the Car Seat, Place the booster seat in recline position 4. ❿...
- Page 32 ❶ Have your child sit in the booster seat, with their back flat against the back of the booster seat. ❷ Thread Vehicle’s Shoulder Belt Through Booster Shoulder Belt Guide in the Headrest ❸ Be sure the lap portion of the vehicle seat belt goes behind the armrests marked with a dark red label.
- Page 33 ❹ Be sure the lap portion of the vehicle seat belt is low across your child’s hips and is adjusted snugly. ❺ Vehicle seat’s shoulder belt should be centered between the child’s neck and edge of shoulder. Raise or lower the headrest to change the shoulder belt location on the child. Reversely folded situation is not allowed on shoulder belt and waist belt.
- Page 34 body support wedge Body Support ❶ Body support must be used if shoulders are below the lowest harness setting. To remove, unbuckle the buckle and pull out the body support. ❷ For infants 0-5 kg, use the body support wedge. Remove the wedge for infants over 5 kg. ❸...
- Page 35 ❹ Cup holder can be on either side. Ⓐ To attach, pull back the seat pad to expose the attachment guide. Ⓑ Slide the cup holder down the guide until it locks into place. Ⓒ To remove, place both hands under the cup holder and push up on the cup holder.
- Page 36 Review your vehicle owner’s manual for seat- ① ing locations. Choose a spacious and flat place that all car doors can be opened to proceed on the installa- tion. In order to guarantee baby’s riding safety, it is suggested that this product is installed on back passenger seat.
- Page 37 ❶ Rear-facing or side-facing vehicle seats. ❷ Rear-facing with an active front air bag. ❸ booster mode with vehicle lap only seat belt Improper use may lead to severe injury or even death of the user. WARNING Review your vehicle owner’s manual for seating locations.
- Page 38 SHOULD NOT create a gap between vehicle seat and booster seat. The front of booster seat base MUST NOT hang over front of vehicle seat. If child will not keep the vehicle seat belt properly positioned, DO NOT use this booster seat. Improper use may lead to severe injury or even death of the user.
- Page 39 • This child restraint system for vehicles is used with car seat belt fixing system, and meets the standards of CNS11497 and ECE R44/04 in Taiwan. This is categorized as “General Type” child restraint system for vehicles. This is a “Universal” or "semi-universal " child restraint system for vehicles. If vehicle manufacturer states in the user manual that the general type for child protecting device is applicable to the car, then this device can be installed in this vehicle correctly.
- Page 40 2-point seat belt. • Seat belt is retracted by both top and bottom sides. • Seat belt is installed with an automatic device. • Seat belt is equipped on a special purpose seat, • such as racecar or sports car. Improper use may lead to severe injury or even death of the user.
- Page 41 Installation using ISOcatch System and 3-point belt or using 3-point belt only (Please do not install using ISOcatch System only) WARNING...
- Page 42 If needed, headrest pad may be removed for cleaning. Ⓐ To remove, unsnap the pad to pull the harness straps out. Ⓑ Pull the plastic tab out of the slots just below the red adjustment handle. Ⓒ Remove the elastic straps from the hooks on both sides of the headrest. Pull pad off of headrest.
- Page 43 If needed, lower seat pad may be removed for cleaning. Ⓐ To remove, unsnap lower seat pad from side pad. Ⓑ Undo the plastic hooks on both armrest. Ⓒ Unhook the elastic strap from both armrests. Pull the pad off. Reverse the steps to reattach the cover on the headrest.
- Page 44 If needed, side pad may be removed for cleaning. Ⓐ To remove, lower headrest and unhook the pad from back. Ⓑ Pull the plastic tabs out from the back and sides of the seat. Ⓒ Remove the elastic straps from the hooks in the forward-facing belt path. Pull the pad off. Reverse the steps to reattach the cover on the headrest.
- Page 45 Cleaning Harness Covers: Wipe clean with damp cloth. Cleaning Crotch Buckle: Recline the car seat and locate the metal retainer. Ⓐ Ⓑ Rotate the metal retainer up through the shell and pad. From the front, pull the crotch buckle out. Ⓒ...
- Page 46 CAUTION Please wipe it gently with a soft dry cloth. Please do not accumulate dirt or paper scrap around the movable part, and carefully remove dirt or paper scrap with a vacuum cleaner. Please use a soft wet cloth, submerged in 40 degrees warm water and dried out slightly, to wipe.
- Page 47 ・ Store instruction manual in the slot with the instruction book icon as shown. Put this product inside a big plastic bag and place it in a location with less dust and without sunlight for storage. When reusing it, if any damage or abnormity is discovered on the main frame, please stop using this product for the sake of the baby’s safety.
- Page 52 SLIMFIT LX ™ Newell Rubbermaid Asia Pacific Limited 2 8 5 0 3 5 5 2 -5 6 8 8 0 3 5 5 2 -5 6 9 0 0 3 6 5 6 -1 2 6 1 0 3 6 5 6 -1 2 6 7 0800@aprica.com.tw...