Table Of Factory's (Defaults) Parameters Settings - Whisper Power 12-2000 User Manual

10 TABLE OF RELEVANT FACTORY (DEFAULTS) PARAMETERS SETTINGS
No. of
config
1107 Maximum current of the AC source
1108 Under voltage of the empty battery
1109 Sub-voltage of the charged battery
1110 Restart voltage of the inverter after under voltage of the battery
1111 Automatic startup at power up
1112 Inverter frequency
1121 Maximum DC voltage for stopping the WPC
1126 Source assistance (Smart Boost) permitted
1127 Grid feeding allowed
1138 Battery charge current
1139 Battery voltage correction according to the temperature
1140 Battery maintenance voltage
1143 Voltage 1 to allow a new battery cycle
1144 Duration of under voltage 1 to allow a new cycle
1145 Voltage 2 to allow a new battery cycle
1146 Duration of under voltage 2 to allow a new cycle
1156 Battery absorption voltage
1157 Duration of absorption
1159 Current at end of absorption
1161 Minimum interval between absorptions
1167 Wave max. of the battery in charger mode (V/cell)
1187 Sensitivity of the charge detection (100% approx.25W)
1188 Number of pulse load research
1189 Time interval between load search pulses
1190 Duration of under voltage of battery before disconnection
1191 Dynamic compensation for under voltage
1194 Battery adaptive low voltage allowed
1195 Max voltage for adaptive low voltage
1198 Time elapsing before transfer relay opens
1199 AC in voltage causing the opening of the transfer relay
1200 Immediate open critical threshold for the transfer
1246 Auxiliary contact 1 activated by voltage 1 {1247} after delays {1248}
1247 Voltage 1under which auxiliary contact 1 is activated
1248 Delays on voltage 1 to activate auxiliary contact 1
1249 Auxiliary contact 1 activated by voltage 2 {1250} after delays {1251}
1250 Voltage 2 under which auxiliary contact 1 is activated
1251 Delays on voltage 2 to activate auxiliary contact 1
1252 Auxiliary contact 1 activated by voltage 3 {1253} after delays {1254}
1253 Voltage 3 under which auxiliary contact 1 is activated
1254 Delays on voltage 3 to activate auxiliary contact 1
1255 Voltage for deactivation of Aux 1
1256 Delays on voltage {1255} to deactivate auxiliary contact 1
1258 Auxiliary contact 1 activated by power 1
1259 Power 1 above which auxiliary contact 1 is activated
1260 Duration of power 1 for activating auxiliary contact 1
1261 Auxiliary contact 1 activated by power 2
1262 Power 2 above which auxiliary contact 1 is activated
1263 Duration of power 2 for activating auxiliary contact 1
1
Setting NC=Factory not changeable
February 2020/ WPC / EN
Denomination / description
FACTORY SETTINGS
Units Fact. Mod.
value value
A 16
V/cell 1.93
V/cell 1.75
V/cell 2
y/n no
Hz 50/60
V/cell 2.84
y/n yes
y/n No
A 45
mV/°C/ -4
cell
V/cell 2.27
V/cell 2.1
min. 30
V/cell 2.05
sec. 60
V/cell 2.4
h 2
Adc 10
h 2
Vdc 0.5 NC 1
% 10
-- 1
sec. 0.8
min. 3
y/n Yes
o/n no
V/cell 2.08
sec. 8
Vac 180/90
Vac 110/55
y/n yes
V/cell 1.97
min. 1
y/n Yes
V/cell 2
min. 10
y/n Yes
V/cell 2.03
min. 60
V/cell 2.27
min. 120
y/n yes
% 70
min. 15
y/n yes
% 100
min. 5
35