Download Print this page
Creative Playthings AH 201-102Q Assembly Manual

Creative Playthings AH 201-102Q Assembly Manual

Pine rock climber

Advertisement

Quick Links

MODEL #AH 201-102Q
ASSEMBLY MANUAL
A
SPECIAL NOTES
• The Rock Climber can only be used on Play Sets with a 5'
platform height.
• All the Hand Holds supplied must be fastened to your Rock
Wall. There should be no unused mounting holes left on
the Rock Wall. These unused holes could present a finger
entrapment hazard to your child.
• Keep the Hand Holds clean so that they can be inspected for
cracks and sharp edges. Replace damaged Hand Holds.
• Replace bolts or weld nuts that are stripped or cross
threaded.
• Review your original Playset Assembly Manual and your
Owners Manual before assembly of your Rock Climber.
• Provide a soft surface free from obstructions 6' out from
the base of the Rock Climber. See your original Playset
Instructions for recommended play surfaces.
All hardware on this set is specially
coated for corrosion resistance. If non-
Creative Playthings hardware is used, it
MUST be galvanized or stainless steel.
PINE ROCK CLIMBER
A 2 ea.
E
B 1 ea.
D
C
C 5 ea.
D 6 ea.
F
E 1 ea.
F 1 ea.
B
4 ea.
26 ea. 17001-104
4 ea.
26 ea. 12017-205
4 ea.
26 ea. 17002-204
4 ea.
24 ea. 17003-609
2 ea.
70 ea. 17138-1025
2 ea.
2 ea.
1 ea.
(12 ea. 15090-400
TOOLS REQUIRED FOR ASSEMBLY
• 7/16" & 1/2" Socket Wrench
• Drill with 1/8", 3/8", & 1" Diameter Bits
• Screwdriver or Drill with T25 Screw Tip (Torx)
• Tape Measure
COMPONENT PARTS
33598-102
Angled Rail 2 x 4 x 68-3/4"
33599-102
Center Rail 2 x 4 x 68-3/4"
32220-102
Rock Board 5/4 x 6 x 46"
32219-102
Spacer Board 5/4 x 6 x 46"
33568-102
Top Rock Board 5/4 x 6 x 46"
40400-100
Knotted Rope
Hex Bolt
Weld Nut
Deck Screw
Lock Washer
Lag Screw
Flat Washer
17001-105
Weld Nut 5/16"
Weld Nut 1/4"
12017-206
Lock Washer 5/16"
Lock Washer 1/4"
12002-206
Flat Washer 5/16"
Flat Washer 8 MM
17003-611
Hex Bolt 5/16-18 x 1-1/2"
Hex Bolt 1/4-20 x 1-1/2"
17003-1609
Hex Bolt 1/4-20 x 4"
T25 Deck Screw, #10 x 2-1/2"
17036-1002
Lag Screw 5/16 x 2-1/2"
14161-400
Access Ladder Bracket
50277-100
Rock Pack (12)
Climbing Rocks)
Access Ladder
Bracket

Advertisement

loading
Need help?

Need help?

Do you have a question about the AH 201-102Q and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Creative Playthings AH 201-102Q

  • Page 1 All hardware on this set is specially • Drill with 1/8", 3/8", & 1" Diameter Bits coated for corrosion resistance. If non- • Screwdriver or Drill with T25 Screw Tip (Torx) Creative Playthings hardware is used, it • Tape Measure MUST be galvanized or stainless steel.
  • Page 2 One opening, 22"-24" wide must be created in the wall of your Playset by removing and repositioning Wall Slats. Save any removed Wall Slats in case they are needed for repair or replacement. 22"-24" PINE ROCK CLIMBER Page 2 © Copyright 2004, Creative Playthings, 19581-700 Rev E (01-18)
  • Page 3 Rock Board then into the Weld Nuts inserted in step 1. Finish securing the Top Rope Board using four #10 x 2-1/2" T25 Screws. Drill a 1/8" diameter pilot hole for each Screw. PINE ROCK CLIMBER Page 3 © Copyright 2004, Creative Playthings, 19581-700 Rev E (01-18)
  • Page 4 A LOOP. THIS PRESENTS EXTREME DANGER TO YOUR CHILDREN. Important: Set the rails of the Rock Climber Set Rails into into the ground so the Rope touches the ground ground. PINE ROCK CLIMBER Page 4 © Copyright 2004, Creative Playthings, 19581-700 Rev E (01-18)