Table of Contents
Advertisement
Quick Links
Read and understand all these safety instructions before using the product.
Do not mount the Desk Base of the Willow Arm on an unstable surface or any surface that could not mount the Desk
Base firmly.
During installation, beware of the recoil of the Willow Arm body when attaching or detaching the monitor to the Willow
Arm. To prevent damage or injury when changing the monitor, always raise the Arm to its highest position before the
monitor is detached. The Willow Arm can support monitors from 1 to 14 pounds.
Do not attempt to disassemble, service or modify the product.
Use only a slightly damp cloth to clean the Willow Arm surface. Never use flammable solvents like alcohol, benzene,
thinner, etc. on the product.
A
Willow Arm Assembly
Qty: 1
B
Quick Release
Bracket
Qty: 1
M4 16mm Screw
M4 8mm Screw
M4 12mm Screw
C
M4x18 Phillips
Screws
7/32" Allen Wrench
1/8" Allen Wrench
Qty: 4
M8 Flat Head Cap Screw
D
M4 16mm Screw
M4x12 Phillips
M4 12mm Screw
Screws
Qty: 4
Plastic Pivot Washer
1/8" Allen Wrench
E
M4 16mm Screw
M4 8mm Screw
M4 12mm Screw
M4x8 Phillips
Screws
Qty: 4
Plastic Pivot Washer
7/32" Allen Wrench
1/8" Allen Wrench
M4 8mm Screw
M4 12mm Screw
Willow
Dual Upgrade Instructions
TM
Important Safety Instructions
Parts grouped by package
F
10mm Plastic
Spacers
Qty: 4
Spacer
G
Pivot Cover Cap
M8 Flat Head Cap Screw
Qty: 1
Plastic Pivot Washer
Steel Washer
H
3/16" Allen
Plastic Cap
Wrench
Qty: 1
M4 8mm Screw
Spacer
Pivot Pin
Plastic Cap
7/32" Allen Wrench
Steel Washer
Spacer
Pivot Pin
Button Head Allen Cap Screw
Steel Washer
M4 16mm Screw
Spacer
I
5/16" x 18 x
1¾" Hex Bolt
Qty: 1
L
Plastic Washer
Qty: 1
O
Plastic
Spacer
Qty: 1
M4 8mm Screw
M4 12mm Screw
7/32" Allen Wrench
1/8" Allen Wrench
Verify that you have all the hardware and tools needed
for the assembly
M4 16mm Screw
M4 12mm Screw
Button Head Allen Cap Screw
Check your packages against the parts list to verify that you
have all the parts needed.
You will also need the following tools:
Plastic Pivot Washer
1/8" Allen Wrench
" end wrench or socket
/
9
16
⅝" end wrench or socket
½" end wrench or socket
J
⅜"x16
Lock Nut
Qty: 2
M
Steel Cup
Qty: 1
M4 16mm Screw
Spacer
Plastic Pivot Washer
Steel Washer
Spacer
Steel Washer
K
Metal
Washer
Qty: 1
N
Pivot
Bushing
Qty: 1
#1500184 - Rev A
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Workrite Ergonomics Willow Dual
Summary of Contents for Workrite Ergonomics Willow Dual
- Page 1 Willow Dual Upgrade Instructions Important Safety Instructions Read and understand all these safety instructions before using the product. Do not mount the Desk Base of the Willow Arm on an unstable surface or any surface that could not mount the Desk Base firmly.
- Page 2 Place Metal Washer (K), Plastic Washer (L) and Steel Cup (M) into original arm and place onto bolt. Attach Lock Nut (J) onto top of bolt. Tighten with ½ " end wrench or socket. Snap Pivot Cover Cap (G) to top of original arm. Workrite Ergonomics 800.959.9675 www.workriteergo.com...
- Page 3 VESA mount will not fit into the mounting location,10mm Plastic Spacers (F) have been supplied. Install these between the monitor and the VESA mount as shown with the shortest M4 screws possible. Note: Keep your Quick Release Bracket (B) for possible future use. Workrite Ergonomics 800.959.9675 www.workriteergo.com...
- Page 4 Do not overtighten or the arm will be too stiff to make easy adjustments in monitor position. Adjust both screws in small, equal steps To increase friction turn screw clockwise To decrease friction turn screw counter-clockwise Friction Adjustment Workrite Ergonomics 800.959.9675 www.workriteergo.com...
Need help?
Do you have a question about the Willow Dual and is the answer not in the manual?
Questions and answers