Altronix NetWay NetWay112 Installation Manual page 2

Fig. 1
www.altronix.com
www.altronix.com
NetWay112
Single Port Injector (Midspan)
12VDC, 1.6A Input
NetWay112
48VDC 15.4W max. per IEEE 802.3af
Single Port Injector (Midspan)
12VDC, 1.6A Input
48VDC 15.4W max. per IEEE 802.3af
I.T.E. 43KC
+ DC ---
Input IN
NetWay112 Port Status and LED Flash Codes
Port Status
I.T.E. 43KC
Non-Powered Device
0Ω < R PORT < 200Ω
Port Open R PORT > 1MΩ
Port On 25kΩ
+ DC ---
Low Signature Resistance
Input IN
300Ω < R PORT < 15kΩ
High Signature Resistance
33KΩ < R PORT < 500kΩ
Port Overload Fault
Installing a NetWayXT/NetWayXTX repeater module:
NetWayXT will work only with PoE devices.
NetWayXTX will work with PoE/PoE+ devices.
1. Mount NetWayXT/NetWayXTX in desired location utilizing the mounting hole (Fig. 4, pg. 3). Use
a proper fastener and/or wall anchor when securing NetWayXT/NetWayXTX to the wall.
2. Connect structured cable from port marked [OUT] on NetWay112 to port marked [IN] on the
NetWayXT/NetWayXTX (Fig. 4, pg. 3, Fig. 1b, pg. 3).
3. Connect structured cable from port marked [OUT] on NetWayXT/NetWayXTX to the PoE camera/
edge device or next NetWayXT/NetWayXTX repeater (Fig. 4, pg. 3).
4. Port status LEDs will illuminate on NetWayXT/NetWayXTX indicating the port is operational
(Fig. 4, pg. 3, refer to Port LED definitions on pg. 2).
5. Power LED will illuminate indicating 12VDC output.
Port LED definitions for NetWayXT repeater:
Status
OFF
ON
Blinking
Port LED definitions for NetWayXTX repeater:
Status PoE/PoE+ Output LED
OFF No PoE/PoE+ Output
ON Normal PoE/PoE+ Output
Blinking
- 2 -
Fig. 1a
Port
Status
Fig. 1c
Power
OUT Shutdown
Flash Code
OFF
OFF
ON
OUT
1 Flash
2 Flashes
5 Flashes
Green LED
Indicates it is connected as 10Base-T or no link.
Indicates it is connected as 100Base-TX.
---------------------------
--- -- --
Fig. 1b
+ ---
Structured
12-16VDC
Cable from
Input
Network
Switch
Structured Cable from
IP Camera, IP Lock or IP device,
NetWay1512 or NetWayXT
Port
Status
Power
Shutdown
l l
Z
l
Z Z
l l l
PoE/PoE+ Input LED
No PoE/PoE+ Input
PoE/PoE+ Input
-------
12VAC to 24VAC or
5VDC to 24VDC Input
for PoE shutdown
12-16VDC
Input
Flash Pattern
LED OFF
LED OFF
LED ON
l l l l
Z
l l l
Z Z
l
Z Z Z Z Z
Yellow LED
Indicates no link.
Indicates a link.
Indicates activity.
Yellow LED
Indicates no link.
Indicates a link.
Indicates activity.
+ ---
Structure
Cable from
Network
Switch
Structu
IP Camera,
NetWay1
l l l
Z
l l
Z Z
l l l l
NetWay112