Download Print this page

Advertisement

Quick Links

Commutator
BK MVE
-4
commutation device between the doorstation
The device is also applied to connect monitors to the video line and a group power supply unit. The unit
recommended for the purpose.
-
Simple apartment number coding similar to BK MV
-
Enhanced noise resistance for video signal distribution
-
Supply voltage to monitors from a power supply unit (BPD) with short-circuit protection and overload protection
-
Automatic recovery after short-circuit or overload
Commutator
BK MVE
-4
Jumpers
Operating instruction
The device does not contain voltage above
Do not make any connections or repair when the power is on.
Caution
.
In case your video doorphone includes monitors with mains-operated switching adaptors (either built-in, or external),
protective earthing connection
WIRING DIAGRAMS
. Protective earthing connection is required to remove voltage from terminals of the device, which
appears due to leakage current flowing from the mains-operated switching adaptors that supply monitors connected to the
device.
Before getting started, make sure that all monitors are disconnected from the mains
For qualified installation, wiring and servicing refer to technical and commercial partners of VIZIT TM. The list of
companies is given on VIZIT.EU (
1
2
- Drill two holes
(1)
in a wall, with
diameter mm and depth
6
- Drive anchors
6х30
(2) into the holes
-
Fix the device by fastening 2 screws
in the anchors
.
Note. Fasteners are not supplied.
Figure1 - Mounting on a wall
www.vizit-group.com
OPERATING INSTRUCTION
(
the device hereinafter
)
/ control unit
-4
PARTS LIST
SAFETY INSTRUCTIONS
30
V
.
shall be carried out as described in the sections
INSTALLATION
http://vizit.eu/eurounion/)
3
30
mm
.
.
3.5х
25
(3)
BK-4MVE Operating Instruction (revision
is intended for operation
and subscriber
devices (monitors and apartment
FEATURES
1
pc.
13
pcs.
1
pc.
.
1
2
(1) - DIN-
rail, width
(2) -
Holder for fixing on a DIN rail
Figure 2 - Mounting on a DIN-rail
with
in
VIZIT
video doorphones as
handsets
BPD
CONNECTIONS
and
EXAMPLES OF
~ 220 .
V
35
mm, depth
1-2
mm
-
201 -
6 12
)
BK MVE
-4
a
UKP).
24/12-1-1
is
1/
8

Advertisement

loading
Need help?

Need help?

Do you have a question about the BK-4MVE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ViziT BK-4MVE

  • Page 1 Before getting started, make sure that all monitors are disconnected from the mains ~ 220 . INSTALLATION For qualified installation, wiring and servicing refer to technical and commercial partners of VIZIT TM. The list of companies is given on VIZIT.EU ( http://vizit.eu/eurounion/)
  • Page 2 The jumper shall be set up only in the top device in the diagram, i.e. in the last BK-4MVE in the video circuit all the rest BK-4MVE devices jumper Z shall be removed ·...
  • Page 3 Lay a trunk protective conductor with yellow-green insulation and copper wire cross-section of 1.5 mm from the main protective conductor of the building to the last BK-4MVE device in the video circuit, which has connected monitors powered from switching adaptors.
  • Page 4 Cable Р Video line Power Coaxial cable Supply Unit Cable А Ground GND circuit Doorstation Control Unit Main protective conductor of the building Figure Example of configuration diagram www.vizit-group.com BK-4MVE Operating Instruction (revision 201 - 6 12...
  • Page 5 Apt. No Apt. No Power Supply Unit Doorstation BPD24 /12- -1 (group) Control Unit +24V Doorstation +12V Figure 6 - Video doorphone with monitors powered from a group power supply unit www.vizit-group.com BK-4MVE Operating Instruction (revision 201 - 6 12...
  • Page 6 +12V Main protective conductor of the building Figure 7 - Video doorphone with monitors powered from a group power supply unit, and monitors with built-in switching adaptor (with protective earthing connection for BK-4MVE) www.vizit-group.com BK-4MVE Operating Instruction (revision 201 -...
  • Page 7: Specifications

    In case additional power supply units are applied, their GND (ground) terminals shall be connected together. For instance, to feed 30 monitors VIZIT -М427С it is recommended to use two units BPD 24/12-1-1 .
  • Page 8 Conductor connecting GND terminals of power supply units BK MVE No 4 To monitors BPD24/12-1-1 BK MVE No To monitors Figure Example of configuration diagram with two Power Supply Units BPD 24/12-1-1. www.vizit-group.com BK-4MVE Operating Instruction (revision 201 - 6 12...