ViziT -M456C Manual

ViziT -M456C Manual

Colour monitor intended for use in video doorphones

Advertisement

VIZIT-M4
56
C
is a colour monitor intended for use in
10
11
1.
Handset
2
.
LED indicator
3.
Preset buttons
-
volume / select ring tone
-
brightness
-
saturation
4.
-
decrease value button
5.
-
increase value / switch to extra camera button
6.
-
MONITOR button
7.
-
DOOR OPEN button
8.
Screen
9.
Male socket
10.
Video OUT jack
(
11. Handset jack
Monitor
VIZIT M 56C
- 4
Screw 3.5 25
-
1
,
3.5 mm) to transfer video to AV-input of TV set
Figure
1 -
Outward Appearance And Controls Layout
x 1
x 3
х
Concrete Insert 6х30
VIZIT
video doorphones.
6
2
3
4
5
PARTS LIST
x 1
Bracket
Fasteners
x 3
8
7
9
Operating Instruction
x 2
Tapping Screw .
2 9х9 5
.
VIZIT-M4
56
C
x 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VIZIT-M456C and is the answer not in the manual?

Questions and answers

Summary of Contents for ViziT VIZIT-M456C

  • Page 1 3.5 mm) to transfer video to AV-input of TV set 11. Handset jack Figure Outward Appearance And Controls Layout PARTS LIST Monitor Bracket Operating Instruction VIZIT M 56C Fasteners Tapping Screw . 2 9х9 5 Screw 3.5 25 х Concrete Insert 6х30...
  • Page 2: Safety Instructions

    SAFETY INSTRUCTIONS CAUTION ! The Monitor does not contain voltage above Do not perform any connections or repair when the power is on. Take care not to spill any liquids or chemically active substances on the product. Unplug the power supply unit before cleaning the monitor. Clean by wiping with dry soft cloth. Do not use any liquid cleaners, aerosol cleaners or abrasive agents.
  • Page 3: Examples Of Wiring Diagrams

    Video Video Figure Plug for the Video OUT jack EXAMPLES OF WIRING DIAGRAMS Extra Camera MONITOR 12 V , 0.3 А VIZIT M 56C Door bell button DATA Power Supply 18 , 0.5А (recommended power supply units: 18/12-1-1, SA03010029 To other apartments...
  • Page 4 Extra Camera MONITOR 12 V , 0.3 А VIZIT M 56C Door bell button DATA LINE BVD 410CBL INDIVIDUAL / STOREY DOORSTATION POWER SUPPLY BPD18/12-1-1 ELECTROMECHANICAL LOCK R 10 OHM) Figure 5 Monitor VIZIT-M456C with individual / storey doorstation and extra camera...
  • Page 5 MONITOR VIZIT M 56C DATA HS/MON EQUIV MONITOR TERMINAL COMMUTATOR VIZIT MT BKM-440 Extra Monitor AW AY RE C ME NU Main Monitor INDIVIDUAL / STOREY DOORSTATION INDIVIDUAL / STOREY DOORSTATION BVD-401СВ BVD 406CB LС ELECTROMECHANICAL ELECTROMECHANICAL LOCK R 10 OHM)
  • Page 6 SETUP Before turning the power on, make sure that there is no misconnection or risk of short circuit. § Turn on the power supply or commutator BKM-440. The monitor LED illuminates with green light. If the LED is dim, the monitor is in the sleep mode (calls are ignored, and all buttons except for are disabled).
  • Page 7: Operation

    OPERATION Having a call from a doorstation, the monitor rings. The image from the doorstation camera appears on the screen Pick up the handset and check duplex intercom. During intercom, press to view image from the extra camera (see Fig. 4, 5, 6), if needed. Press again to switch back to the image from the doorstation camera.

Table of Contents