Mase Generators IS 7.6 Installation Manual
  1. Manuals
  2. Brands
  3. Mase Generators Manuals
  4. Portable Generator
  5. IS 7.6
  6. Installation manual

Mase Generators IS 7.6 Installation Manual

Hide thumbs

Advertisement

Table of Contents

IS7.6
INSTALLATION
MANUAL
#12501

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IS 7.6 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Mase Generators IS 7.6

Summary of Contents for Mase Generators IS 7.6

  • Page 1 IS7.6 INSTALLATION MANUAL #12501...
  • Page 2 1" 1" 29-7/8" Fig. 1 Fig. 2 Fig. 3 Fig. 4...
  • Page 3 Fig. 5 Fig. 6 Fig. 7...
  • Page 4 Fig. 9 Fig. 8 Anti-siphon valve Fig. 10 Fig. 11 Fig. 12...
  • Page 5 Fig. 13 Fig.14 Fig.15...
  • Page 6 GEN. MAIN LOAD Fig. 17 WIRING DIAGRAM REFERENCES 1 - Hour Meter 2 - Circuit breaker 3 - Isolator 4 - Power terminal board 5 - Capacitors 6 - Stator 7 - Rotor 8 - Alternator 9 - Thermal switch 10 - START / STOP-Preheating button 11 - Engine protection module Fig.

  • Page 7: Wiring Diagram

    WIRING DIAGRAM MACHINE CODE: 001060 - 001096 - 001135 - 001134 - 001129 - 001137 Fig. 18...
  • Page 8 INDEX Photos/illustrations ........................ 2-6 Wiring diagram ........................7 GENERAL INFORMATION .................... 9 Purpose and application of this manual ................9 Symbols .......................... 9 Recommendations for safety during installation and setup ........10 INSTALLATION ......................10 Space requirements ......................10 Fastening the unit ......................10 Ventilation ........................

  • Page 9: General Information

    1 GENERAL INFORMATION It is very important you read and understand this manual before operating the generator. THE WARRANTY OF THIS PRODUCT MAY BE VOIDED IF THE SPECIFICATIONS CONTAINED IN THIS INSTALLATION MANUAL ARE NOT FOLLOWED. 1.1 Purpose and application of this manual Thank you for choosing a mase generator.

  • Page 10: Installation

    2. Recommendations for safety during installation and setup Raw water feed system Boats usually use one of two systems to collect water (fig. 3): - The personnel in charge of installation and initial starting of the generator must always wear safety 1 - Direct infeed system glasses and protective gloves.
  • Page 11 13 Anti-siphon valve The muffler (fig.4, ref.6) collects A - Hose -inside diameter 50 mm (1.96") , suitable for the water in the exhaust hoses when the generator raw water/exhaust gas. motor is turned off, thus preventing it from flowing B - Hose - inside diameter 15 mm (.59"), suitable for raw into the motor through the exhaust manifold and water.

  • Page 12: Electrical Connections

    For further information, read the Anti-siphon valve must be inserted engine instruction manual, supplied by the engine between the inlet of the sea water pump and exhaust manufacturer. manifold as indicated in Fig. 11 The drainage duct of the anti-siphon valve must run 6 ELECTRICAL CONNECTIONS beneath the valve itself in order to prevent water accumulating in the duct, which should always...
  • Page 13 - The generator is equipped with a circuit breaker which cuts the power in the event of an overload or short-circuit. Table of characteristics for single voltage 49.5 IS 6.5 24.8 IS 7.6 27.5 Table of characteristics for double voltage IS 6.5 24.8 IS 7.6 27.5...

This manual is also suitable for:

I.s.6.5

Table of Contents