Related Manuals for Ingersoll-Rand Liftchain LC2H060S
Summary of Contents for Ingersoll-Rand Liftchain LC2H060S
- Page 1 Product Information Liftchain Industrial Hydraulic Hoist Models LC2H060S, LC2H120D, LC2H180T and LC2H250Q Save These Instructions Form MHD56465 Edition 3 June 2011 45923638 2011 Ingersoll-Rand Company ©...
-
Page 2: Product Description
Only allow trained technicians to perform maintenance on this product. For additional information contact factory or nearest Ingersoll Rand Ingersoll Rand Distributor. For additional supporting documentation refer to Table 1 ‘Product Information Manuals’ on page 2. Manuals can be downloaded from www.ingersollrandproducts.com. The use of other than genuine Ingersoll Rand replacement parts may result in safety hazards, decreased performance and increased maintenance and will invalidate all warranties. -
Page 3: Specifications
SPECIFICATIONS Model Code Explanation Example: LC2H060SIF0RE3M0A LC2H060S Liftchain Hydraulic Hoist Capacity and Chain Falls LC2H060S = 6000 kg (13,200 lbs), single fall LC2H120D = 12,000 kg (26,500 lbs), double fall LC2H180T = 18,000 kg (39,700 lbs), triple fall LC2H250Q = 25,000 kg (55,000 lbs), quad fall Application = Industrial Body Control Type... -
Page 4: Installation
Table 2: Specifications Nominal Recommended Chain Unit Net Weight with Maximum Rated Hoist Weight of Chain Minimum Load Flow Pressure @ Load Standard 10 ft (3 m) Lifting Hoist Capacity Working per meter of lift Headroom Chain Rated Load Size Lift Speed Model... -
Page 5: Operation
Use a premium anti-wear (AW) hydraulic fluid in the hydraulic system. The following NOTICE specifications are intended to serve as a general guide in selecting suitable oils. • Make certain to adjust the balance chain so that the chain container does not Table 5: Recommended Hydraulic Oil contact the load chain. - Page 6 1. Oil Temperature. The presence of hot fluid in a hydraulic system is a primary 4. When first operating the hoist it is recommended that the hoist be driven slowly in both directions for a few minutes. cause of poor operation, component failure and system downtime. The fluid used 5.
-
Page 7: General Lubrication
LUBRICATION To replace oil remove fill plug and add oil to the reduction gear assembly, replace To ensure continued satisfactory operation of hoist, all points requiring lubrication plug. Refer to Product Parts Information Manual. must be serviced with correct lubricant at proper time interval as indicated for each assembly. -
Page 8: Warranty
WARRANTY Ingersoll Rand Limited Warranty IR's maximum liability is limited to the purchase price of the Product and in no event Ingersoll Rand Company (“IR”) warrants to the original user its material handling shall IR be liable for any consequential, indirect incidental or special damages of any products (“Products”) to be free of defects in material and workmanship for a period nature arising from the sale or use of the Product, whether in contract, tort or of one year from the date of purchase. -
Page 9: Product Information Graphics
PRODUCT INFORMATION GRAPHICS One Direction of Lifting 40 cm3 Counter Balance Valve Top Limit no-load Relief Valve Ingersoll Rand Calibration Pressure Bottom Limit Relief Valve (Dwg. MHP3135) Lifting Port (Dwg. MHP3136) Throat Width (Dwg. MHP1300) (Dwg. MHP0040) (Dwg. MHP0111) (Dwg. MHP0102) Form MHD56465 Edition 3... - Page 10 PRODUCT INFORMATION GRAPHICS CONTINUED Rack Hoist Trolley Drive Assembly Mounted This Side. Lower Beam Maintain clearance between rack Flange and pinion teeth of 0.16 inch (minimum) to 0.20 inch (maximum) [4 to 5 mm] to prevent pinion binding during operation. Measure gap Pinion between the outside diameter of drive pinion and root of rack segment.
-
Page 11: Service Notes
SERVICE NOTES Form MHD56465 Edition 3... - Page 12 www.ingersollrandproducts.com...