Table of Contents
Advertisement
Speakers
Switch off power to the game. The woofer is mounted behind a grille at the back of the drivers seat. The
smaller full range speakers are mounted behind the seat headrest grilles. The larger full range speakers
are mounted behind the grilles above the video monitor. Remove the screws and set the grille aside.
Always remove the upper mounting screws first and replace them last to avoid damage to the speaker.
Remove the speakers from the enclosure and disconnect the wires.
not
polarity.
Do
use excess force when removing or tightening mounting screws threaded
Gear Shift Assembly
Switch off power to the game. Remove shift plate mounting screws. Disconnect cables. Lift up and out.
Pedal
Assembly
Switch off power to the game. Unlock and remove the rear door. Disconnect the pedal cable assembly
from the wiring harness. Adjust the seat to the maximum rear position. Remove six outer mounting
screws from the front perimeter of the pedal plate. Pull assembly toward seat until it clears the opening,
then lift it up and away from the cabinet.
Power
Supply
Switch off power to the game. Disconnect the line cord. Unlock and remove the rear door. Unplug the
IEC AC. connector and the wiring harnesses from the top of the supply. Leave the terminal strip alone.
Disconnect the D.C. power cable from the hard disk drive. Do not remove the supply mounting bracket or
the line filter (found on European models only). Remove four front and two rear screws from the supply,
then slide it out of the cabinet. Verify the line voltage switch setting before reinstalling the power supply.
Game
Electronics
Switch off power to the game. Unlock and remove the rear door. Remove the screws and slowly swing
the metal enclosure cover open. You may apply power with the cover open if necessary to observe the
indicators. Disconnect cables and remove mounting screws to replace circuit boards. Anti-static bags
and protective containers from new parts must be used to store the component if it is not reinstalled.
Sound l/O Board Assembly
Switch off power to the game. Unlock and open the rear door and the coin door. Remove the screws and
slowly swing the metal enclosure cover open. Carefully note the orientation of the JAMMA connector and
the other cables. Extract the harnesses from the board connectors. Remove six mounting screws and
washers from the Sound l/O Board Assembly. Carefully remove the Sound I/O Board, rocking it gently to
separate the PCI edge connector from the CPU Board Assembly. Lii the board up and off the posts.
Upon reinstallation, tighten the screws starting at the center and working toward the outer edge. Use anti-
static bags and protective containers from new parts to store the board if not reinstalled.
CPU Board Assembly
Switch off power to the game. Unlock and open the rear door and the coin door. Remove the screws and
slowly swing the metal enclosure cover open. Carefully note the orientation of the JAMMA connector and
the other cables. Extract the harnesses and the hard disk drive ribbon cable from their board connectors.
Loosen screws and disconnect the VGA cable from the CPU Board connector. Remove the six mounting
screws and washers from the Sound I/O Board Assembly. Carefully remove the Sound l/O Board, rocking
it gently to separate the PCI edge connector from the CPU Board Assembly. Lift it up and out. Set the
Sound Board aside. Remove six screws and washers holding the CPU Board Assembly to the enclosure.
Carefully separate the CPU Board from the Video Card PCI connector, rocking it gently to separate the
edge connector from the board. Upon reinstallation, tighten the screws of both the CPU Board Assembly
and Sound I/O Board Assembly in order, starting at the centers and working toward the outer edges of the
boards. Use anti-static bags and protective containers from new parts to store the board if not reinstalled.
Video Card Assembly
Switch off power to the game. Unlock and open the rear door and the coin door. Remove the screws and
slowly swing the metal enclosure cover open. Carefully note the orientation of the JAMMA connector and
the other cables. Extract the harnesses and the hard disk drive ribbon cable from their board connectors.
Disconnect and remove the Sound I/O Board Assembly and the CPU Board Assembly and set them
aside. Loosen the screws and disconnect the VGA cable from the Video Card output connector. Remove
the Video Card. Use anti-static bags and protective containers to store the assembly if not reinstalled.
Mark each wire to ensure proper
4-5
into plastic.
Advertisement
Table of Contents
