Summary of Contents for KANSAI SPECIAL RX/UTC Series
Page 1
INSTRUCTION INSTRUCTION INSTRUCTION INSTRUCTION RX/UTC MANUAL Industrial Industrial Sewing Industrial Industrial Sewing Sewing Sewing Machines Machines Machines Machines First published : September 1991 Eighth edition : July 2001 No. 010086...
Page 2
INTRODUCTION INTRODUCTION INTRODUCTION INTRODUCTION Thank you for your purchasing Kansai Special's RX/UTC Series. Read and study this instruction manual carefully before beginning any of the procedures and save it for later use. This instruction manual describes adjustments maintenance procedures for the thread trimmer.
CONTENTS CONTENTS CONTENTS CONTENTS 1. HOW TO USE THE THREAD TRIMMER 10. ADJUSTING THE PRESSER FOOT LIFT ・ 2. INSTALLING THE POSITION DETECTOR 11. ADJUSTING THE TOP COVER THREAD TRIMMER ・ 3. ADJUSTING THE THREAD TRIMMER AIR CYLINDER 11-1 Relationship between the position of the movable knife and the stationary knife ・・...
【1】HOW TO USE THE THREAD TRIMMER < Note > Do not use this thread trimmer with no fabric under the presser foot. ■ P ressing the pedal with toe (position A) starts the machine. Releasing the pedal (position B) stops the needle at the top/bottom of its stroke (adjustable with the motor).
【3】ADJUSTING THE THREAD TRIMMER AIR CYLINDER 3 3 3 3 - - - - 1 Air cylinder stroke 1 Air cylinder stroke 1 Air cylinder stroke 1 Air cylinder stroke The stroke of the air cylinder should be approximately 15mm. To adjust this stroke, loosen collar B and screw A.
【5】ADJUSTING THE THREAD TRIMMER 5 5 5 5 - - - - 1 Position of the movable knife and the stationary knife 1 Position of the movable knife and the stationary knife 1 Position of the movable knife and the stationary knife 1 Position of the movable knife and the stationary knife ■ ...
5 5 5 5 - - - - 4 Adjusting the st 4 Adjusting the st 4 Adjusting the stationary knife holder stopper 4 Adjusting the st ationary knife holder stopper ationary knife holder stopper ationary knife holder stopper The stationary knife holder I slides to the left and stops by stationary knife holder stopper J.
There should be a clearance of 0mm between movable knife and the top surface of looper. The adjustment is made by loosening screw X and moving stationary knife holder guide. After the above adjustment, make sure the movable and stationary knife holders move smoothly.
【6】ADJUSTING THE THREAD RELEASER 6 6 6 6 - - - - 1 Thread releaser block 1 Thread releaser block 1 Thread releaser block 1 Thread releaser block With the thread trimmer air cylinder rod at the left end (the air cylinder is not operating), set the clearance between thread trimmer air cylinder bracket A and thread releaser block B at 13mm.
6 6 6 6 - - - - 4 Thread releaser plate 4 Thread releaser plate 4 Thread releaser plate 4 Thread releaser plate Install thread releaser bar D to thread releaser bar connection plate F with screw G. The top end of thread releaser bar D should protrude 39mm from the top surface of thread releaser bar guide E.
【8】ADJUSTING THE SPEED CONTROLLER AND AIR PRESSURE ■ S peed controller F controls the speed when the thread trimmer knife holder protrudes. Speed controller G controls the speed when the thread trimmer knife holder retracts. If screw F is too loosened, the holder will protrude too fast and then the position of the movable knife will be unstable, causing cutting error.
【10】ADJUSTING THE PRESSER FOOT LIFT ■ F oot lift on the machine with spreader 6mm above the top surface of the needle plate ■ F oot lift on the machine without spreader 7mm above the top surface of the needle plate To make the above adjustment, loosen screw D for crank lever C and then set the clearance between slot A on the presser bar clamp connection plate and screw...
【11】ADJUSTING THE TOP COVER THREAD TRIMMER 11- - - - 1 Relationship between the position of the movable knife and the stationary knife 1 Relationship between the position of the movable knife and the stationary knife 1 Relationship between the position of the movable knife and the stationary knife 1 Relationship between the position of the movable knife and the stationary knife When the movable knife retracts all the way, align hook point E of the movable knife with hook point F of the stationary knife.
11- - - - 4 Adjusting the movable knife left to right 4 Adjusting the movable knife left to right 4 Adjusting the movable knife left to right 4 Adjusting the movable knife left to right Movable knife C should pass clearance B between spreader A and the left needle.
11- - - - 7 Adjusting the 7 Adjusting the 7 Adjusting the 7 Adjusting the solenoid return spring solenoid return spring solenoid return spring solenoid return spring Available for the electric top cover thread trimmer. Position spring bracket D so that screw E will be centered in the slot of spring bracket D. Set the clearance between drive lever B and solenoid shaft A at approximately 2mm.
【12】WIRING AND PIPING FOR PNEUMATIC DEVICES 12- - - - 1 RX9800 1 RX9800 1 RX9800 1 RX9800 ■ C onnect air lines and cords by referring to the illustration below and the parts list. 12- - - - 2 RX9800ALK 2 RX9800ALK,...