Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for KANSAI SPECIAL WX8803/UTC
Summary of Contents for KANSAI SPECIAL WX8803/UTC
- Page 1 INSTRUCTION INSTRUCTION INSTRUCTION INSTRUCTION WX,LX/UTC MANUAL Industrial Industrial Industrial Industrial Sewing Sewing Sewing Sewing Machines Machines Machines Machines WX8803/UTC LX5801/UTC First published : August 1997 Fourth edition : August 2000 No. 000056...
- Page 2 INTRODUCTION INTRODUCTION INTRODUCTION INTRODUCTION Thank you for your purchasing Kansai Special's WX/UTC Series. Read and study this instruction manual carefully before beginning any of the procedures and save it for later use. This instruction manual describes adjustments maintenance procedures for the thread trimmer.
-
Page 3: Table Of Contents
CONTENTS CONTENTS CONTENTS CONTENTS 1. HOW TO USE THE THREAD TRIMMER 10. ADJUSTING THE PRESSER FOOT LIFT ･･ 2. INSTALLING THE POSITION DETECTOR 11. ADJUSTING THE TOP COVER THREAD TRIMMER ･ 3. ADJUSTING THE THREAD TRIMMER AIR CYLINDER 11-1 Relationship between the position of the movable knife and the stable knife ･･････... -
Page 4: How To Use The Thread Trimmer
【1】HOW TO USE THE THREAD TRIMMER < Note > Do not use this thread trimmer with no fabric under the presser foot. ■ Pressing the pedal with toe (position A) starts the machine. Releasing the pedal (position B) stops the needle at the top/bottom of its stroke (adjustable with the motor). -
Page 5: Adjusting The Thread Trimmer Air Cylinder
【3】ADJUSTING THE THREAD TRIMMER AIR CYLINDER 3 3 3 3 - - - - 1 Air cylinder stroke 1 Air cylinder stroke 1 Air cylinder stroke 1 Air cylinder stroke The stroke of the air cylinder should be approximately 15mm. Adjustment is made by loosening collar B and screw A. -
Page 6: Adjusting The Thread Trimmer
【5】ADJUSTING THE THREAD TRIMMER 5 5 5 5 - - - - 1 Position of the movable knife and the stationary knife 1 Position of the movable knife and the stationary knife 1 Position of the movable knife and the stationary knife 1 Position of the movable knife and the stationary knife ■... -
Page 7: Adjusting The Movable Knife Holder Left And Right
5 5 5 5 - - - - 4 Adjusting the mov 4 Adjusting the mov 4 Adjusting the mov 4 Adjusting the movable knife holder left and right able knife holder left and right able knife holder left and right able knife holder left and right With movable knife A at the extreme left end of its travel, there should be a distance of 23mm from the... -
Page 8: Adjusting The Movable Knife Up And Down
5 5 5 5 - - - - 6 Adjusting the movable knife up and down 6 Adjusting the movable knife up and down 6 Adjusting the movable knife up and down 6 Adjusting the movable knife up and down There should be a clearance of 0.2mm between movable knife and the top surface of looper. -
Page 9: Adjusting The Thread Releaser
【6】ADJUSTING THE THREAD RELEASER 6 6 6 6 - - - - 1 Thread releaser block 1 Thread releaser block 1 Thread releaser block 1 Thread releaser block With the thread trimmer air cylinder rod or the solenoid rod at the left end of its travel (the air cylinder is not operating), there should be a clearance of 4.0mm between the thread trimmer air cylinder bracket D and thread releaser block C. -
Page 10: Looper Thread Take-Up
6 6 6 6 - - - - 4 Looper thread take 4 Looper thread take 4 Looper thread take 4 Looper thread take- - - - up This machine is equipped with looper thread take-up L. Thread looper thread take-up L with a looper thread. -
Page 11: Adjusting The Speed Controller And Air Pressure
【8】ADJUSTING THE SPEED CONTROLLER AND AIR PRESSURE 8 8 8 8 - - - - 1 Adjusting the speed controller 1 Adjusting the speed controller 1 Adjusting the speed controller 1 Adjusting the speed controller Speed controller F controls the speed when the thread trimming knife holder projects. -
Page 12: Adjusting The Presser Foot Lift
【10】ADJUSTING THE PRESSER FOOT LIFT ■ Foot lift on the machine with spreader 6mm above the top surface of the needle plate ■ Foot lift on the machine without spreader 7mm above the top surface of the needle plate To make the above adjustment, loosen screw D on crank lever C and set the clearance between slot A on the presser bar clamp... -
Page 13: Adjusting The Top Cover Thread Trimmer
【11】ADJUSTING THE TOP COVER THREAD TRIMMER 11- - - - 1 Relationship between the position of the movable knife and the stable knife 1 Relationship between the position of the movable knife and the stable knife 1 Relationship between the position of the movable knife and the stable knife 1 Relationship between the position of the movable knife and the stable knife When the movable knife fully retracts, align hook point E of the movable knife with point F of the stationary knife. -
Page 14: Adjusting The Movable Knife Left To Right
< Note > The following adjustments should be made manually with the fabric under the presser foot when the needle is at the top of its stroke. 11- - - - 4 Adjusting the movable knife left to right 4 Adjusting the movable knife left to right 4 Adjusting the movable knife left to right 4 Adjusting the movable knife left to right Movable knife C should pass clearance B between... -
Page 15: Adjusting The Solenoid Return Spring
11- - - - 7 Adjusting the solenoid return spring 7 Adjusting the solenoid return spring 7 Adjusting the solenoid return spring 7 Adjusting the solenoid return spring Available for the electric top cover thread trimmer. Position spring bracket D so that screw E will be centered in the slot of spring bracket D. Set the clearance between the end of drive lever B and the step of solenoid shaft A at approximately 2mm. -
Page 16: Wiring And Piping For Pneumatic Devices
【12】WIRING AND PIPING FOR PNEUMATIC DEVICES ■ Connect air lines and cords by referring to the illustration below and the parts list. 【13】WIRING AND PIPING FOR ELECTRIC DEVICES ■ Connect air lines and cords by referring to the illustration below and the parts list.