Subscribe to Our Youtube Channel
Related Manuals for Watts PVI Aqua Solve Family
Summary of Contents for Watts PVI Aqua Solve Family
- Page 1 INSTALLATION MANUAL Aqua Solve Family (AQS-9) Aqua Solve Large (AQS-14) 400498/05-15...
- Page 2 UNPACKING YOUR WATER SOFTENER UNPACKING YOUR WATER SOFTENER UNPACKING YOUR WATER SOFTENER 1 Valve Cover and Electronic Faceplate 2 Salt Lid 1 Valve Cover and Electronic Faceplate 1 Valve Cover and Electronic Faceplate 3 Salt Cabinet 2 Salt Lid 2 Salt Lid 4 Resin Cylinder 3 Salt Cabinet 3 Salt Cabinet...
- Page 3 IDENTIFYING MAJOR PARTS OF YOUR IDENTIFYING MAJOR PARTS OF YOUR WATER SOFTENER WATER SOFTENER Description Quantity Part No. Description Quantity Part No. 1 pair Easy Install Tees* GO817 Easy Install Tees* 1 pair G0817 (incorporates check value) (incorporates check value) 7208718 Drain/ Overflow Tubing Drain/Overflow Tubing...
-
Page 4: Safety Information
The installation must conform to them. interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in Do not locate the softener where freezing temperatures occur. Do not accordance with the instructions, may cause harmful interference to radio attempt to treat water over 49ºC. - Page 5 INSTALLATION OF YOUR WATER SOFTENER INSTALLATION OF YOUR WATER SOFTENER PLANNING AND SITING THE INSTALLATION SPECIFICATION REQUIREMENTS The installation of a water softener is relatively easy, but we PLANNING AND SITING THE INSTALLATION SPECIFICATION REQUIREMENTS Maximum water temperature 49 °C (120 °F) recommend that this work is undertaken by an authorised agent.
- Page 6 STEP BY STEP GUIDE TO PLUMBING STEP BY STEP GUIDE TO PLUMBING THE SOFTENER THE SOFTENER PLUMBING water back on, make sure the bypass is open and the inlet and outlet PLUMBING make sure the bypass is open and the inlet and outlet valves are closed. valves are closed.
- Page 7 CONNECT TRANSFORMER STEP BY STEP GUIDE TO PLUMBING 1. Connect the power cable leads to the two terminals on the transformer. THE SOFTENER (CONTINUED) NOTE: Check to be sure all lead wire connections are secure on the back of the faceplate. CAUTION: Be sure all wiring is away from the valve gear and motor area, which rotates during recharges.
- Page 8 Programming the Water Softener Programming the Water Softener Programming the Water Softener Programming the Water Softener Low Salt Low Salt Low Salt Low Salt LED Indicator LED Indicator LED Indicator LED Indicator Display Display Display Display UP button UP button UP button UP button DOWN button...
-
Page 9: Set Salt Type
Programming the Water Softener Programming the Water Softener Programming the Water Softener Programming the Water Softener Programming the Water Softener C. SET RECHARGE (REGENERATION) SALT LEVEL” should show in the display. Otherwise, C. SET RECHARGE (REGENERATION) C. SET RECHARGE (REGENERATION) SALT LEVEL"... -
Page 10: Recharge Now
The softener enters the fill cycle of regeneration immediately. “RECHARGE NOW” will flash during the regeneration. When completed (in about 2 hours), full water conditioning capacity is restored. NOTE: If the “Clean Feature” is set ON, the normal Controller Features / Options Controller Features / Options regeneration cycle is preceded by a cleaning backwash and rinse. -
Page 11: Adding Salt
Routine Maintenance Routine Maintenance ADDING SALT BREAKING A SALT BRIDGE ADDING SALT BREAKING A SALT BRIDGE ADDING SALT BREAKING A SALT BRIDGE Lift the salt lid and check the salt storage level Sometimes, a hard crust or salt “bridge” forms in the ift the salt lid and check the salt storage level fre- Sometimes, a hard crust or salt “bridge”... -
Page 12: Troubleshooting Guide
2. Fuse blown, circuit breaker popped, or cir- Replace fuse, reset circuit breaker, or switch circuit on, overflow drain connected together by a tee. cuit switched off (See “Power Outage and then use RECHARGE NOW feature. 5. Low or high system water pressure (low If pressure is low, increase well pump output to a mini- Memory”... -
Page 13: Troubleshooting
Troubleshooting Troubleshooting RESETTING TO FACTORY DEFAULTS RESETTING TO FACTORY DEFAULTS To reset the electronic controller to its factory default RESETTING TO FACTORY DEFAULTS for all settings (time, hardness, etc.): To reset the electronic controller to its factory default for To reset the electronic controller to its factory default all settings (time, hardness, etc.): 1. - Page 14 NOTES...
- Page 15 NOTES...
Need help?
Do you have a question about the PVI Aqua Solve Family and is the answer not in the manual?
Questions and answers