Fitting Accessories; Maintenance - Black+Decker SVB520JW-B5 Manual

Discharge
• The LED (3) is green when discharging.
• The LED flashes green when low battery.
• The LED flashes RED for 10 seconds once fully
discharged.
• The LED flashes RED when the rorary brush is jammed
or entangled. Please refer to section 'Removing and
cleaning the rotary brushes'.
• Once the unit is fully discharged, the LED (3) will flash
RED for 10 seconds every time the handvac or stick vac
ON/OFF switch is pressed and the unit will not turn on.
A charge cycle is required before the unit will turn on.
Hand vac accessories (Fig. F)
Your hand vac may be supplied with some of the following
accessories.
• The brush tool (8) is designed for more effective
cleaning of upholstered furniture and fabric.
• The crevice tool (9) allows for vacuuming in narrow and
hard to-reach places.

Fitting accessories

• Insert the appropriate accessory into the front of the
hand vac (1) as show in figure F.
• Make sure the accessory is fully pushed in.
Note: When not in use the accesories can be stored in the
storage recesses (8a) and (9a).
Switching ON and OFF
Hand vac mode
• To switch ON, press the On/Off power switch (2).
• To switch OFF, press the On/Off power switch ( 2 ).
Stick vac mode
• To switch On, press the stick vac On/Off button (15).
• For decreased performance press the speed selection
switch (14).
• To switch OFF, press the stick vac On/Off button (15).
Note: Return the product to the charger immediately after
use so that it will be ready and fully charged for the next use.
Ensure that the product is fully engaged with the charger
plug.The unit must be placed on charge for it to run once it is
fully discharged.
Emptying and cleaning (Fig. H, I, J, K, L)
• Press the dust bowl release button (4) and pull the dust
bowl (5) straight off as shown in figure H.
• While holding the dust bowl over an appropriate waste
receptacle, pull out the filter assembly (19) as shown in
figure I.
(Original instructions)
• Empty the dust bowl (5) into an appropriate waste
receptacle as shown in figure J
• Rotate filter (20) counterclockwise to unlock and remove
it from the pre filter assembly (19). Gently remove any
debris.
• Rinse out the dust-bowl with warm soapy water as
shown in figure L.
• Wash the filters with warm soapy water as shown in
figure L.
• Make sure the filters are dry before reassembling.
• Refit the filters into the dust bowl and ensure that they
are correctly seated.
• replace the dust bowl onto the hand vac making sure the
release latch (4) clicks into place.
Warning! Never use the appliance without the filters.
Optimum dust collection will only be achieved with a clean
filter.
Removing and cleaning the rotary brushes
(Fig. M)
Warning! To reduce the risk of injury from moving parts,
disconnect the floor head from the stick vac before cleaning
or servicing.
• To remove the rotary brush (6b), lift the plastic tab (6a)
located on the floor head (6).
• Lift the rotary brush (6b) out of the floor head. Clear the
brushes of any hair or other debris that may have
accumulated.
• Replace rotary brush, and secure plastic tab before
using vacuum.
Safe storage
The unit can be safely stored, when not in use, either by
utilising the wall mount (17) or releasing the handle lock (12)
and lowering the handle (13) to allow for storage in confined
areas.

Maintenance

Your BLACK+DECKER cordless appliance has been
designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
• Run the battery down completely if it is integral and then
switch off.
• Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular
cleaning.
ENGLISH
7