Signal Booster Specifications; Warnings - Wilson Electronics SIGNALBOOST Sleek 2B5225 Installation Manual

Signal Booster Specifications

Model Number / Part Number
Connectors
Impedance (input/output)
Frequency
Passband Gain (nominal)
1
20 dB Bandwidth (nominal)
2
Power output for single cell phone (uplink)
Power output for single received channel (downlink)
3,4
received channels (downlink). The
maximum power is reduced by the
number of channels:
Noise Figure (typical)
Isolation
Power Requirements
Notes:
1. Nominal gain is the maximum gain at any frequency in the passband.
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB
lower than the passband amplification. One of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer's rated output power of this equipment is for single carrier operation. For situations when multiple carrier
signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can
cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by
an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.

Warnings:

Warning:
Warning:
Warning
Warning:
(a) antenna location ensures at least a 30 inch separation distance from all persons,
(b) antenna gain less cable loss does not exceed 15 dBi, and
(c) such antennas are not operating in conjunction with any other antennas, or transmitting devices.
Warning:
All Wilson Electronics products are protected by Wilson's 30-day money-back guarantee. If, for any reason, the performance of any product is not acceptable, simply return
the product directly to the reseller with a dated proof of purchase.
Wilson Electronics amplifiers are warranted for one (1) year against defects in workmanship and / or materials. Warranty issues may be resolved by returning the
product directly to the reseller with a dated proof of purchase.
Amplifiers may also be returned directly to the manufacturer at the consumer's expense, with a dated proof of purchase and a Returned Material Authorization (RMA)
number supplied by Wilson Electronics. Wilson shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced
product back to the original consumer within the continental United States.
This warranty does not apply to any amplifiers determined by Wilson Electronics to have been subjected to misuse, abuse, neglect, or mishandling that alters or
damages physical or electronic properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of this device.
Disclaimer: The information provided by Wilson Electronics, Inc. is believed to be complete and accurate. However, no responsibility is assumed by Wilson
Electronics, Inc. for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its
use.Copyright © 2008 Wilson Electronics, Inc. All rights reserved.
Wilson
800 MHz (uplink/downlink)
1900 MHz (uplink/downlink)
Power output for multiple
Number of
channels
Do not plug in the power supply until the outside antenna cable is attached to the Sleek
RF Safety: The Sleek cradle/amplifier must be installed with a separation of at least 8
™
inches from all persons and must not be located in conjunction with any other antenna or
amplifier.
RF Safety: The FCC requires that a cell phone with cradle attached may only be used
with the cradle mounted as illustrated in this installation guide. A cell phone held near the
ear must be without the cradle attached.
RF Safety: The Outside Antennas authorized for use with this amplifier are shown on page
1 of this guide. Other antennas may be used, but only in fixed installations when located
outside of a building or structure (not in mobile/ portable installations), provided that:
DO NOT use phone covers that have chrome or any other metallic surface. It may block
cellular signals
30-Day Money-Back Guarantee
Electronics, Inc.
®
Dual Band
800/1900 MHz Specifications
2B5225/815225,815226, 815226F
SMA Female
50 ohms
824-894 MHz / 1850-1990 MHz
20 dB (typical) / 30 dB (maximum)
43 MHz / 45 MHz
112 MHz / 84MHz
800 MHz
CDMA 28.9 dBm
GSM 30.9 dBm
EDGE 30.9 dBm
WCDMA 30.13 dBm
800 MHz
CDMA -9 dBm
GSM -1.3 dBm
EDGE -1.3 dBm
WCDMA .32 dBm
Maximum Power
800 MHz
2 -1.1 dBm
3 -4.7 dBm
4 -7.2 dBm
5 -9.1 dBm
6 -10.7 dBm
3 dB nominal
> 40 dB
5V DC, 1A
1-Year Warranty
Phone: 800-204-4104 Fax: 435-656-2432
#110807 - Sleek™ Install Guide English - REV.02-- 08.26.10
1900 MHz
31.8 dBm
32.6 dBm
31.9 dBm
31.4 dBm
1900 MHz
1.0 dBm
1.8 dBm
2.1 dBm
2.3 dBm
3
1900 MHz
2.2 dBm
-1.4 dBm
-3.9 dBm
-5.8 dBm
-7.4 dBm
.
™